|
|
|
| General Information | |
|
|
|
|
|
|
PRODUCT SPECIFICATIONS |
|
|
|
|
|
|
|
|
|
|
|
Pressure - (PSI / BAR) | 3100 / 213 |
| 3500 / 241 |
| 4000 / 276 |
Flow Rate - (GPM / LPM) | 2.8 / 10.6 |
| 3.6 / 13.6 |
| 4.0 / 15.1 |
|
|
|
|
|
|
Water Supply Temperature - (°F / C°) |
|
| 100 / 38 Max |
|
|
|
|
|
|
|
|
Hose Length - (Feet / Meters) |
| 35 / 10.7 |
| 50 / 15.2 | |
|
|
|
|
|
|
Nozzles - Number per Unit |
| 5 |
|
| |
Lance Length (Inches / cm) | 20 / 51 |
| 33 / 84 |
| 33 / 84 |
Gun |
|
| Professional |
|
|
|
|
|
|
|
|
Engine Displacement - (Cubic Inch / cc) | 12.9 / 212 |
| 18.4 / 302 |
| 25.6 / 420 |
|
|
|
|
|
|
Spark Plug Type |
| F7TC or equivalent |
| F6TC or equivalent | |
Spark Plug Gap - (Inches / mm) |
|
| |||
Fuel Capacity - (Quarts / Liters) | 3.7 / 3.5 |
| 5.8 / 5.5 |
| 6.9 / 6.5 |
Engine Oil Capacity - (Oz / Liters) | 20 / 0.6 |
| 37 / 1.1 |
| 37 / 1.1 |
|
|
|
|
|
|
Low Oil Shut Down System |
|
| Yes |
|
|
|
|
|
|
|
|
On / Off Switch |
|
| Yes |
|
|
EMISSIONS INFORMATION
The U.S. Environmental Protection Agency (and California Air Resource Board for equipment certified to CA standards) requires that this engine comply with exhaust and evaporative emission standards. Locate the emissions compliance decal on the engine to determine what standards the engine meets, and to determine which emissions warranty applies. The engine is certified to meet the applicable emission standards on gasoline. It is important to follow the maintenance specifications in the Maintenance section to ensure that the engine complies with the applicable emission standards for the duration of the product’s life. This engine utilizes lean carburetion settings and other systems to reduce emissions. Tampering with or altering the emission control system may increase emissions and may be a violation of Federal or California Law. Acts that constitute tampering include but are not limited to:
•Removal or alteration of any part of the intake, fuel, or exhaust systems
•Altering or defeating the governor linkage or
If you are aware of any of the following symptoms, have your engine inspected and repaired by your servicing dealer:
•Hard starting or stalling after starting
•Rough idle
•Misfiring or backfiring under load
•Afterburning (backfiring)
•Black exhaust smoke or high fuel consumption
HIGH ALTITUDE OPERATION
The fuel system on this engine may be influenced by operation at higher altitudes. Proper operation can be ensured by installing an altitude kit when required. See the table below to determine when an altitude kit is required. Operating this engine without the proper altitude kit installed may increase the engine’s emissions and decrease fuel economy and performance. Kits may be obtained from any Dealer, and should be installed by a qualified individual.
Altitude Range* |
| Kit Number |
| PSI |
|
|
|
|
|
0 - 5000 Feet |
| Not Required |
| 3100/3500 |
|
|
|
|
|
0 - 3000 Feet |
| Not Required |
| 4000 |
|
|
|
|
|
3000 - 6000 Feet |
| 0J5275 |
| 4000 |
|
|
|
|
|
6000 - 8000 Feet |
| 0J5275A |
| 4000 |
|
|
|
|
|
5000 - 7000 Feet |
| 0K2016 |
| 3100 |
|
|
|
|
|
5000 - 7000 Feet |
| 0K2017 |
| 3500 |
|
|
|
|
|
| *Elevation above sea level. |
| ||
NOTE:
If the altitude kit has been installed and the engine will be operated at an altitude where the kit is not required, the engine should be returned to the original factory configuration. Operating the engine at lower altitudes with the kit installed may cause the engine to overheat and result in serious engine damage, and may result in decreased performance and increased emissions.
5