CHANGE LIGHT BULBS

WARNING

Observe all safety warning and precautions! Improper light bulb removal or replacement could result in Death or Serious Injury.

Disconnect power from opener before beginning this task.

When replacing light cover, make sure wires are not pinched or near moving parts.

1.Disconnect power to door opener.

Open powerhead light cover.

Remove light bulb(s).

Replace with maximum 100 Watt light bulb(s).

Do NOT use light bulbs with greater than 100 Watt rating.

Close powerhead light cover.

2.Reconnect power to door opener.

Test light operation.

MOTION DETECTOR* - OVERVIEW

(Not available on all models)

Powerheads equipped with a motion detector sensor provide additional security when

exiting or entering the garage area.

*This sensor works by detecting body heat. Range of detection may be reduced when the temperature in the garage is close to body temperature.

NOTE: Detector positioning on the powerhead provides for monitoring below the powerhead.

OPERATION

Detector sensor is always ON. There are NO user controls or adjustments.

Lights automatically turn ON when a change is detected and will turn OFF after 4 minutes of no change.

Motion detector sensor will not turn OFF lighting turned ON at the wall console.

Lighting turned ON at the wall console will remain ON until wall console turns lighting OFF or opener

is used.

Motion Detector

RESET - OPEN/CLOSE TRAVEL LIMIT

Performing all ten (10) Limits/Force setting steps (pages 6-7) erases previous Limits/Force settings.

NOTE: The opener will not close the door automatically unless the Safe-T-Beam® System is installed and Limits are programmed.

©2010 The Genie Company

CARRIAGE ENGAGE/DISENGAGE

Use Release Handle to manually connect or release chain or belt bullet to Carriage.

TO RELEASE CARRIAGE:

1. Pull handle DOWN then let go.

2. Manually move door until carriage releases from bullet.

3. Raise or lower door manually.

 

NOTICE

 

 

IFDOORBECOMESOBSTRUCTED

 

Release

PULLDOWNONHANDLE

DOOR

PULL

 

Handle

 

TO RECONNECT CARRIAGE:

1.Verify RED block is in the UP position.

2.Manually move door until carriage engages bullet.

3.Raise or lower door using remote or wall console.

FIG. 6-3 Carriage Release

DOOR

ENGAGE

DISENGAGE

(for installation)

(for installation)

TO REENGAGE PULL

TO DISENGAGE

DOWN AND TOWARD

PULL DOWN AND

POWERHEAD THEN

TOWARDS DOOR

LET GO

THEN LET GO

TO RELEASE or RECONNECT CARRIAGE,

 

PULL DOWN AND LET GO

 

FIG. 6-4 Carriage Release (cut away view)

19

12/2010

Page 19
Image 19
Genie 3024 Door, Change Light Bulbs, Motion DETECTOR* Overview, Reset OPEN/CLOSE Travel Limit, Carriage ENGAGE/DISENGAGE

3024H, 3024 specifications

The Genie 3024 and 3024H are part of Genie’s renowned line of compact scissor lifts, designed primarily for vertical access to elevated workspaces in various environments. With a remarkable blend of performance and ease of use, these models cater to the needs of contractors, maintenance crews, and facility managers alike.

One of the standout features of the Genie 3024 and 3024H is their impressive working height, which reaches up to 30 feet. This elevates the platform’s capabilities, allowing operators to complete tasks efficiently in tight spaces. The platform itself is spacious, providing ample room for tools and materials, which enhances productivity on the job site.

Both models are equipped with Genie’s patented Fast Mast technology, enabling users to elevate the platform quickly to the desired height while keeping the base on the ground. This feature significantly reduces downtime, making it easier for operators to complete tasks efficiently without unnecessary delays. This characteristic is especially beneficial in industries where time is of the essence.

The Genie 3024 and 3024H also come with a robust electric drive and hydraulic system, ensuring smooth and reliable operation both indoors and outdoors. Their compact size and tight turning radius allow them to navigate through narrow aisles and doorways with ease, making them ideal for use in warehouses, retail spaces, and smaller construction sites.

The models are designed with safety and stability in mind. They include features such as non-slip surfaces on the platform, automatic cut-off systems, and guardrails to ensure secure usage during operation. Additionally, the units are equipped with integrated wheel brakes that enhance safety when the lifts are stationed in elevated positions.

The Genie 3024H variant offers added flexibility with its high-capacity battery system, providing extended work cycles without the interruption of recharging. This makes the 3024H particularly suitable for extended job sites and projects where access to power might be limited.

In summary, the Genie 3024 and 3024H scissor lifts deliver an array of features that enhance both performance and safety, making them invaluable tools for anyone needing reliable vertical lift solutions. With a focus on compact design, quick operational capabilities, and enhanced safety measures, these models exemplify Genie’s commitment to meeting the evolving needs of the construction and maintenance industries.