WARNING

• Garage door hardware (springs, cables, brackets,

pulleys, etc.) are under extreme pressure and

tension.

DO NOT attempt to repair or adjust door

springs or any hardware, and DO NOT OPERATE

garage door automatically or manually if door

is improperly balanced or springs are broken.

WARNING

Use wall console supplied with opener. Other approved wall consoles may be available. Unapproved or incompatible wall consoles can cause the opener to operate unexpectedly.

Safe-T-Beam® (STB) SYSTEM CHECK

• STB Red and Green LEDs ON steady, system OK

CONTACT A TRAINED DOOR SYSTEM

TECHNICIAN.

ROUTINE MONTHLY MAINTENANCE

Basic monthly maintenance tasks.

Safe-T-Beam® System Check

Door balance

Contact reverse

Instructions for these tasks and others are found on

STB Red LED flashes

Check for obstruction

Check alignment

Verify wire routing from STBs to STB connection in powerhead

Check for signal interference from another Safe-T-Beam® unit

FROM STBs

STB

FROM WALL

CONSOLE

NOT NOT

USED USED

BWC IWC

the following pages.

DOOR BALANCE (SPRING TENSION)

No STB Red or Green LED displayed

Check wiring and wire connections

With the door closed, pull release handle DOWN and let go to release door carriage assembly from drive system.

Raise door manually approximately 3’- 4’ and release.

Door should remain stationary or move very slightly.

If door moves quickly, CONTACT A TRAINED DOOR SYSTEM TECHNICIAN.

Close the door.

Verify RED block in carriage is in the up position. (refer to page 19)

Operate door using remote or wall console.

Door will re-attach itself to carriage assembly.

3’ - 4’

Sectional Door

FIG. 6-1 Door balance

3’ - 4’

One-Piece Door

CONTACT REVERSE TEST (Monthly test)

The Force and Limit settings MUST be COMPLETED before testing. (See pages 6-7)

1.Test.

Open garage door using wall console.

Place a 2" x 4" board (laid flat) under center of garage door opening (Fig. 6-2).

Close garage door using wall console.

When door contacts board, the door must stop (within 2 seconds) and reverse direction returning to open position.

2.Adjustment.

If the door:

Stops before it contacts the 2 x 4 board, it may simply be responding to an improperly set down limit. Return to pages 6-7 and repeat steps 1 through 10 to correct down limit.

Stops after contacting the 2 x 4 board and does not reverse, it may need an adjustment to the down limit. Return to pages 6-7 and repeat steps 1 through 10 to correct down limit.

Test again. Repeat as necessary until door reverses upon contacting board.

FIG. 6-2 2 x 4 under center of door opening

18

©2010 The Genie Company

12/2010

Page 18
Image 18
Genie 3024H manual Routine Monthly Maintenance, Safe-T-Beam System Check Door balance Contact reverse, Test, Adjustment

3024H, 3024 specifications

The Genie 3024 and 3024H are part of Genie’s renowned line of compact scissor lifts, designed primarily for vertical access to elevated workspaces in various environments. With a remarkable blend of performance and ease of use, these models cater to the needs of contractors, maintenance crews, and facility managers alike.

One of the standout features of the Genie 3024 and 3024H is their impressive working height, which reaches up to 30 feet. This elevates the platform’s capabilities, allowing operators to complete tasks efficiently in tight spaces. The platform itself is spacious, providing ample room for tools and materials, which enhances productivity on the job site.

Both models are equipped with Genie’s patented Fast Mast technology, enabling users to elevate the platform quickly to the desired height while keeping the base on the ground. This feature significantly reduces downtime, making it easier for operators to complete tasks efficiently without unnecessary delays. This characteristic is especially beneficial in industries where time is of the essence.

The Genie 3024 and 3024H also come with a robust electric drive and hydraulic system, ensuring smooth and reliable operation both indoors and outdoors. Their compact size and tight turning radius allow them to navigate through narrow aisles and doorways with ease, making them ideal for use in warehouses, retail spaces, and smaller construction sites.

The models are designed with safety and stability in mind. They include features such as non-slip surfaces on the platform, automatic cut-off systems, and guardrails to ensure secure usage during operation. Additionally, the units are equipped with integrated wheel brakes that enhance safety when the lifts are stationed in elevated positions.

The Genie 3024H variant offers added flexibility with its high-capacity battery system, providing extended work cycles without the interruption of recharging. This makes the 3024H particularly suitable for extended job sites and projects where access to power might be limited.

In summary, the Genie 3024 and 3024H scissor lifts deliver an array of features that enhance both performance and safety, making them invaluable tools for anyone needing reliable vertical lift solutions. With a focus on compact design, quick operational capabilities, and enhanced safety measures, these models exemplify Genie’s commitment to meeting the evolving needs of the construction and maintenance industries.