Manuals / Genie / Lawn and Garden / Utility Vehicle

Genie GTH-1056, GTH-1048 General Safety Procedures, Welding Precautions, Hand Holds And Steps

Models: GTH-1048 GTH-1056

1 64

Download 64 pages 39.11 Kb

Page 18

WELDING PRECAUTIONS

GENERAL SAFETY

GENERAL SAFETY PROCEDURES

WELDING PRECAUTIONS

CAUTION

Any unauthorized welding can cause structural failure or possible personal injury. DO NOT weld on any structural member. All unauthorized welding will void the warranty.

HAND HOLDS AND STEPS

WARNING

Slips and falls can cause serious injury.

When getting on and off the machine, always maintain a three point contact with steps and hand rails while facing the machine.

DO NOT use the steering wheel or any other controls as handrails.

NEVER jump on or off the machine.

Be careful of slippery conditions on platforms, steps and handrails when getting on and off the machine.

ALWAYS shut off the engine before leaving the operator's station.

REFUELING

WARNING

Fires can cause death or severe personal injury.

Handle fuel with care. It is highly flammable. DO NOT refuel the machine while smoking or when near open flames or sparks.

ALWAYS stop the engine before refueling the machine. Fill the fuel tank outdoors.

Prevent fires by keeping the machine clean of trash, grease and

debris. ALWAYS clean up spilled fuel.

2 - 4

Image 18

Genie GTH-1056, GTH-1048 manual General Safety Procedures, Welding Precautions, Hand Holds And Steps, Refueling

Contents

GTH-1048 GTH-1056 with Maintenance InformationOperator’s Manual First Edition Second PrintingTABLE OF CONTENTS SECTION SECTION SECTION SECTION SECTION SECTIONSECTION ROUGH TERRAIN FORK LIFT SAFETY TABLE OF CONTENTS SECTION 1 - ROUGH TERRAIN FORK LIFT SAFETYINTRODUCTION ROUGH TERRAIN FORK LIFT SAFETYTHIS SYMBOL MEANS YOUR SAFETY IS INVOLVED! READ, UNDERSTAND AND FOLLOW ALL DANGER, WARNING AND CAUTION DECALS ON YOUR ROUGH TERRAINSYMBOLS STANDARDS AND SYMBOLSROUGH TERRAIN FORK LIFT SAFETY STANDARDSSAFETY TRAINING AND KNOWLEDGEROUGH TERRAIN FORK LIFT SAFETY OPERATORS RESPONSIBILITIES ROUGH TERRAIN FORK LIFT SAFETYMANAGEMENTS RESPONSIBILITIES ROUGH TERRAIN FORK LIFT SAFETYMAINTENANCE AND REPAIR ROUGH TERRAIN FORK LIFT SAFETYOPERATION SAFETY ROUGH TERRAIN FORK LIFT SAFETYROUGH TERRAIN FORK LIFT SAFETY OPERATION SAFETY13. Lifting Loads ROUGH TERRAIN FORK LIFT SAFETY OPERATION SAFETY18. Traveling on slopes/grades ROUGH TERRAIN FORK LIFT SAFETY SECTION GENERAL SAFETY General Safety Procedures SECTION 2 - GENERAL SAFETYTABLE OF CONTENTS Proper Load Chart UseSAFETY ALERT SYMBOL GENERAL SAFETYGENERAL SAFETY PROCEDURES THE OPERATORWELDING PRECAUTIONS GENERAL SAFETYGENERAL SAFETY PROCEDURES HAND HOLDS AND STEPSHYDRAULIC SAFETY GENERAL SAFETYGENERAL SAFETY PROCEDURES SERVICE TIRES SAFELYPRACTICE SAFE MAINTENANCE GENERAL SAFETYGENERAL SAFETY PROCEDURES BOOM SAFETYGENERAL SAFETY PROCEDURES DANGERGENERAL SAFETY AVOID ELECTRICAL POWER LINESJUMP STARTING GENERAL SAFETYJUMP STARTING PROPER LOAD CHART USE GENERAL SAFETYGENERAL SAFETY PROPER LOAD CHART USESECTION CONTROLS AND INSTRUMENTS SECTION 3 - CONTROLS AND INSTRUMENTS TABLE OF CONTENTSCONTROLS AND INSTRUMENTS OPERATORS COMPARTMENTA - Boom Down B - Boom Up JOYSTICK CONTROL FUNCTIONSCONTROLS AND INSTRUMENTS C - Boom Out D - Boom InJOYSTICK CONTROL FUNCTIONS BUTTON PUSHED CONTROLS AND INSTRUMENTSA - Tilt Down B - Tilt Back SERVICE BRAKES PARKING BRAKECONTROLS AND INSTRUMENTS FRAME SWAY CONTROL CONTROLS AND INSTRUMENTSCONTROLS AND INSTRUMENTS GAUGESHYDRAULIC PUMP DESTROKE BUTTON DANGERSTEERING TRANSMISSIONCONTROLS AND INSTRUMENTS FRONT AXLE DIFFERENTIAL LOCK CONTROLS AND INSTRUMENTSLEFT FRONT STABILIZERSCONTROLS AND INSTRUMENTS RIGHTENGINE ELECTRONIC CONTROL UNIT CONTROLS AND INSTRUMENTSJohn Deere Engine Electronic Control Unit Blink Code Diagnostics CONTROLS AND INSTRUMENTSENGINE ELECTRONIC CONTROL UNIT ENGINE ELECTRONIC CONTROL UNIT Fault Codes and DescriptionsCONTROLS AND INSTRUMENTS 2-Digit CodeSECTION OPERATION SECTION 4 - OPERATION TABLE OF CONTENTSOPERATION AND SAFETY GUIDELINES OPERATIONBEFORE STARTING THE ENGINE OPERATIONDANGER STARTING THE ENGINE DANGEROPERATION DANGERSTARTING THE ENGINE OPERATIONCheck the dash mounted gauges for logical readings BEFORE OPERATING THE FORKLIFTOPERATION Operate the joystick controller momentarily in all directionsOPERATION BEFORE OPERATING THE FORKLIFTOperate the frame sway control A momentarily right and left BEFORE OPERATING THE FORKLIFT DANGER OPERATIONNever operate the machine with a faulty backup alarm. Doing so may result in serious injury or death OPERATIONBEFORE OPERATING THE FORKLIFT DANGER TRANSPORTING A LOAD OPERATIONOPERATION TRANSPORTING A LOADAlways keep the boom retracted to ensure greater stability OPERATION PLACING A LOAD WARNINGBDo not sway the machine with the boom angle indicator arrow DANGEROPERATION PLACING A LOADTraveling with a reading of more than 0 degress on the boom angle indicator arrow A may cause a rollover hazard DANGERGTH-1048 & GTH-1056 OPERATIONPLACING A LOAD OPERATION SECTION MAINTENANCE PROCEDURES General Safety Practices SECTION 5 - MAINTENANCE PROCEDURESTABLE OF CONTENTS Daily MaintenanceMAINTENANCE PROCEDURES GENERAL SAFETY PRACTICESBEFORE SERVICING HYDRAULIC SAFETY MAINTENANCE PROCEDURESGENERAL SAFETY PRACTICES WELDING PRECAUTIONSSCHEDULEDMAINTENANCE DAILY MAINTENANCEMAINTENANCE PROCEDURES PERFORM ENGINE MAINTENANCESetting 50 PSI MAINTENANCE PROCEDURESDAILY MAINTENANCE CHECK HYDRAULIC OIL LEVELSECTION MATERIAL SAFETY DATA Material Safety Data Sheets SECTION 6 - MATERIAL SAFETY DATATABLE OF CONTENTS California Proposition 65 WarningsMATERIAL SAFETY DATA MATERIAL SAFETY DATA SHEETS MSDSCALIFORNIA PROPOSITION 65 WARNINGS MATERIAL SAFETY DATAWash hands after handling