Manuals / Genie / Lawn and Garden / Utility Vehicle

Genie GTH-1056 Maintenance Procedures, Daily Maintenance, Check Hydraulic Oil Level, Location

Models: GTH-1048 GTH-1056

1 64

Download 64 pages 39.11 Kb

Page 60

Image 60

MAINTENANCE PROCEDURES

DAILY MAINTENANCE

CHECK HYDRAULIC OIL LEVEL

Location:	Sight glass (B). Behind the rear panel.
To Check:	Move the machine to level ground.
	Level the frame.
	Completely retract the boom.	B
	Completely retract the boom.
	Position the forks level.
	Lower the boom to the ground.
	Oil should be visible 1/2 way in the sight glass.

NOTE: Refer to page 5-24 of this manual for the proper oil

specifications and capacities.

CHECK TIRE FOR PROPER INFLATION

Location: Wheel ends.

To Check: With the valve stem (C) positioned to the top of the tire, check the tire pressure with the tire cold and a properly functioning air pressure gauge.

Setting: 50 PSI.

All tires require a calcium chloride ballast or an optional foam fill to be operated safely. The loss of ballast can affect the machine's stability and cause a rollover hazard, resulting in damage, injury or death.

5 - 6

Page 60

Image 60

Genie GTH-1056 Maintenance Procedures, Daily Maintenance, Check Hydraulic Oil Level, Location, To Check, Setting 50 PSI

Contents

with Maintenance Information Operator’s ManualGTH-1048 GTH-1056 First Edition Second PrintingTABLE OF CONTENTS SECTION SECTION SECTION SECTION SECTION SECTIONSECTION ROUGH TERRAIN FORK LIFT SAFETY TABLE OF CONTENTS SECTION 1 - ROUGH TERRAIN FORK LIFT SAFETYROUGH TERRAIN FORK LIFT SAFETY THIS SYMBOL MEANS YOUR SAFETY IS INVOLVED! READ, UNDERSTAND ANDINTRODUCTION FOLLOW ALL DANGER, WARNING AND CAUTION DECALS ON YOUR ROUGH TERRAINSTANDARDS AND SYMBOLS ROUGH TERRAIN FORK LIFT SAFETYSYMBOLS STANDARDSSAFETY TRAINING AND KNOWLEDGEROUGH TERRAIN FORK LIFT SAFETY OPERATORS RESPONSIBILITIES ROUGH TERRAIN FORK LIFT SAFETYMANAGEMENTS RESPONSIBILITIES ROUGH TERRAIN FORK LIFT SAFETYMAINTENANCE AND REPAIR ROUGH TERRAIN FORK LIFT SAFETYOPERATION SAFETY ROUGH TERRAIN FORK LIFT SAFETYROUGH TERRAIN FORK LIFT SAFETY OPERATION SAFETY13. Lifting Loads ROUGH TERRAIN FORK LIFT SAFETY OPERATION SAFETY18. Traveling on slopes/grades ROUGH TERRAIN FORK LIFT SAFETY SECTION GENERAL SAFETY SECTION 2 - GENERAL SAFETY TABLE OF CONTENTSGeneral Safety Procedures Proper Load Chart UseGENERAL SAFETY GENERAL SAFETY PROCEDURESSAFETY ALERT SYMBOL THE OPERATORGENERAL SAFETY GENERAL SAFETY PROCEDURESWELDING PRECAUTIONS HAND HOLDS AND STEPSGENERAL SAFETY GENERAL SAFETY PROCEDURESHYDRAULIC SAFETY SERVICE TIRES SAFELYGENERAL SAFETY GENERAL SAFETY PROCEDURESPRACTICE SAFE MAINTENANCE BOOM SAFETYDANGER GENERAL SAFETYGENERAL SAFETY PROCEDURES AVOID ELECTRICAL POWER LINESJUMP STARTING GENERAL SAFETYJUMP STARTING PROPER LOAD CHART USE GENERAL SAFETYGENERAL SAFETY PROPER LOAD CHART USESECTION CONTROLS AND INSTRUMENTS SECTION 3 - CONTROLS AND INSTRUMENTS TABLE OF CONTENTSCONTROLS AND INSTRUMENTS OPERATORS COMPARTMENTJOYSTICK CONTROL FUNCTIONS CONTROLS AND INSTRUMENTSA - Boom Down B - Boom Up C - Boom Out D - Boom InJOYSTICK CONTROL FUNCTIONS BUTTON PUSHED CONTROLS AND INSTRUMENTSA - Tilt Down B - Tilt Back SERVICE BRAKES PARKING BRAKECONTROLS AND INSTRUMENTS FRAME SWAY CONTROL CONTROLS AND INSTRUMENTSGAUGES HYDRAULIC PUMP DESTROKE BUTTONCONTROLS AND INSTRUMENTS DANGERSTEERING TRANSMISSIONCONTROLS AND INSTRUMENTS FRONT AXLE DIFFERENTIAL LOCK CONTROLS AND INSTRUMENTSFRONT STABILIZERS CONTROLS AND INSTRUMENTSLEFT RIGHTENGINE ELECTRONIC CONTROL UNIT CONTROLS AND INSTRUMENTSJohn Deere Engine Electronic Control Unit Blink Code Diagnostics CONTROLS AND INSTRUMENTSENGINE ELECTRONIC CONTROL UNIT Fault Codes and Descriptions CONTROLS AND INSTRUMENTSENGINE ELECTRONIC CONTROL UNIT 2-Digit CodeSECTION OPERATION SECTION 4 - OPERATION TABLE OF CONTENTSOPERATION AND SAFETY GUIDELINES OPERATIONBEFORE STARTING THE ENGINE OPERATIONSTARTING THE ENGINE DANGER OPERATIONDANGER DANGERSTARTING THE ENGINE OPERATIONBEFORE OPERATING THE FORKLIFT OPERATIONCheck the dash mounted gauges for logical readings Operate the joystick controller momentarily in all directionsOPERATION BEFORE OPERATING THE FORKLIFTOperate the frame sway control A momentarily right and left BEFORE OPERATING THE FORKLIFT DANGER OPERATIONNever operate the machine with a faulty backup alarm. Doing so may result in serious injury or death OPERATIONBEFORE OPERATING THE FORKLIFT DANGER TRANSPORTING A LOAD OPERATIONOPERATION TRANSPORTING A LOADAlways keep the boom retracted to ensure greater stability PLACING A LOAD WARNINGB Do not sway the machine with the boom angle indicator arrowOPERATION DANGERPLACING A LOAD Traveling with a reading of more than 0 degress on the boom angle indicator arrow A may cause a rollover hazardOPERATION DANGERGTH-1048 & GTH-1056 OPERATIONPLACING A LOAD OPERATION SECTION MAINTENANCE PROCEDURES SECTION 5 - MAINTENANCE PROCEDURES TABLE OF CONTENTSGeneral Safety Practices Daily MaintenanceMAINTENANCE PROCEDURES GENERAL SAFETY PRACTICESBEFORE SERVICING MAINTENANCE PROCEDURES GENERAL SAFETY PRACTICESHYDRAULIC SAFETY WELDING PRECAUTIONSDAILY MAINTENANCE MAINTENANCE PROCEDURESSCHEDULEDMAINTENANCE PERFORM ENGINE MAINTENANCEMAINTENANCE PROCEDURES DAILY MAINTENANCESetting 50 PSI CHECK HYDRAULIC OIL LEVELSECTION MATERIAL SAFETY DATA SECTION 6 - MATERIAL SAFETY DATA TABLE OF CONTENTSMaterial Safety Data Sheets California Proposition 65 WarningsMATERIAL SAFETY DATA MATERIAL SAFETY DATA SHEETS MSDSCALIFORNIA PROPOSITION 65 WARNINGS MATERIAL SAFETY DATAWash hands after handling