Manuals / Genie / Lawn and Garden / Utility Vehicle

Genie GTH-1056, GTH-1048 manual Starting The Engine, Operation

Models: GTH-1048 GTH-1056

1 64

Download 64 pages 39.11 Kb

Page 44

Image 44

OPERATION

STARTING THE ENGINE

CAUTION

If the engine fails to start within 30 seconds release the key, wait at least 2 minutes to allow the starter motor to cool before trying again. If the engine fails to start after four attempts, trouble shoot and correct the problem. DO NOT turn the key if the engine is running. This may cause damage to the starter motor.

CAUTION

Attempting to start the engine by towing or pushing the machine will result in damage to the powershift transmission and will not start the engine! It also is an unsafe practice that could cause personal injury.

4 - 6

Page 44

Image 44

Genie GTH-1056, GTH-1048 manual Starting The Engine, Operation

Contents

with Maintenance Information Operator’s ManualGTH-1048 GTH-1056 First Edition Second PrintingTABLE OF CONTENTS SECTION SECTION SECTION SECTION SECTION SECTIONSECTION ROUGH TERRAIN FORK LIFT SAFETY TABLE OF CONTENTS SECTION 1 - ROUGH TERRAIN FORK LIFT SAFETYROUGH TERRAIN FORK LIFT SAFETY THIS SYMBOL MEANS YOUR SAFETY IS INVOLVED! READ, UNDERSTAND ANDINTRODUCTION FOLLOW ALL DANGER, WARNING AND CAUTION DECALS ON YOUR ROUGH TERRAINSTANDARDS AND SYMBOLS ROUGH TERRAIN FORK LIFT SAFETYSYMBOLS STANDARDSROUGH TERRAIN FORK LIFT SAFETY SAFETYTRAINING AND KNOWLEDGE OPERATORS RESPONSIBILITIES ROUGH TERRAIN FORK LIFT SAFETYMANAGEMENTS RESPONSIBILITIES ROUGH TERRAIN FORK LIFT SAFETYMAINTENANCE AND REPAIR ROUGH TERRAIN FORK LIFT SAFETYOPERATION SAFETY ROUGH TERRAIN FORK LIFT SAFETY13. Lifting Loads ROUGH TERRAIN FORK LIFT SAFETYOPERATION SAFETY 18. Traveling on slopes/grades ROUGH TERRAIN FORK LIFT SAFETYOPERATION SAFETY ROUGH TERRAIN FORK LIFT SAFETY SECTION GENERAL SAFETY SECTION 2 - GENERAL SAFETY TABLE OF CONTENTSGeneral Safety Procedures Proper Load Chart UseGENERAL SAFETY GENERAL SAFETY PROCEDURESSAFETY ALERT SYMBOL THE OPERATORGENERAL SAFETY GENERAL SAFETY PROCEDURESWELDING PRECAUTIONS HAND HOLDS AND STEPSGENERAL SAFETY GENERAL SAFETY PROCEDURESHYDRAULIC SAFETY SERVICE TIRES SAFELYGENERAL SAFETY GENERAL SAFETY PROCEDURESPRACTICE SAFE MAINTENANCE BOOM SAFETYDANGER GENERAL SAFETYGENERAL SAFETY PROCEDURES AVOID ELECTRICAL POWER LINESJUMP STARTING JUMP STARTINGGENERAL SAFETY PROPER LOAD CHART USE GENERAL SAFETYGENERAL SAFETY PROPER LOAD CHART USESECTION CONTROLS AND INSTRUMENTS SECTION 3 - CONTROLS AND INSTRUMENTS TABLE OF CONTENTSCONTROLS AND INSTRUMENTS OPERATORS COMPARTMENTJOYSTICK CONTROL FUNCTIONS CONTROLS AND INSTRUMENTSA - Boom Down B - Boom Up C - Boom Out D - Boom InA - Tilt Down B - Tilt Back JOYSTICK CONTROL FUNCTIONS BUTTON PUSHEDCONTROLS AND INSTRUMENTS CONTROLS AND INSTRUMENTS SERVICE BRAKESPARKING BRAKE FRAME SWAY CONTROL CONTROLS AND INSTRUMENTSGAUGES HYDRAULIC PUMP DESTROKE BUTTONCONTROLS AND INSTRUMENTS DANGERCONTROLS AND INSTRUMENTS STEERINGTRANSMISSION FRONT AXLE DIFFERENTIAL LOCK CONTROLS AND INSTRUMENTSFRONT STABILIZERS CONTROLS AND INSTRUMENTSLEFT RIGHTJohn Deere Engine Electronic Control Unit ENGINE ELECTRONIC CONTROL UNITCONTROLS AND INSTRUMENTS ENGINE ELECTRONIC CONTROL UNIT Blink Code DiagnosticsCONTROLS AND INSTRUMENTS Fault Codes and Descriptions CONTROLS AND INSTRUMENTSENGINE ELECTRONIC CONTROL UNIT 2-Digit CodeSECTION OPERATION SECTION 4 - OPERATION TABLE OF CONTENTSOPERATION AND SAFETY GUIDELINES OPERATIONBEFORE STARTING THE ENGINE OPERATIONSTARTING THE ENGINE DANGER OPERATIONDANGER DANGERSTARTING THE ENGINE OPERATIONBEFORE OPERATING THE FORKLIFT OPERATIONCheck the dash mounted gauges for logical readings Operate the joystick controller momentarily in all directionsOperate the frame sway control A momentarily right and left OPERATIONBEFORE OPERATING THE FORKLIFT BEFORE OPERATING THE FORKLIFT DANGER OPERATIONBEFORE OPERATING THE FORKLIFT DANGER Never operate the machine with a faulty backup alarm. Doing so may result in serious injury or deathOPERATION TRANSPORTING A LOAD OPERATIONAlways keep the boom retracted to ensure greater stability OPERATIONTRANSPORTING A LOAD PLACING A LOAD WARNINGB Do not sway the machine with the boom angle indicator arrowOPERATION DANGERPLACING A LOAD Traveling with a reading of more than 0 degress on the boom angle indicator arrow A may cause a rollover hazardOPERATION DANGERPLACING A LOAD GTH-1048 & GTH-1056OPERATION OPERATION SECTION MAINTENANCE PROCEDURES SECTION 5 - MAINTENANCE PROCEDURES TABLE OF CONTENTSGeneral Safety Practices Daily MaintenanceBEFORE SERVICING MAINTENANCE PROCEDURESGENERAL SAFETY PRACTICES MAINTENANCE PROCEDURES GENERAL SAFETY PRACTICESHYDRAULIC SAFETY WELDING PRECAUTIONSDAILY MAINTENANCE MAINTENANCE PROCEDURESSCHEDULEDMAINTENANCE PERFORM ENGINE MAINTENANCEMAINTENANCE PROCEDURES DAILY MAINTENANCESetting 50 PSI CHECK HYDRAULIC OIL LEVELSECTION MATERIAL SAFETY DATA SECTION 6 - MATERIAL SAFETY DATA TABLE OF CONTENTSMaterial Safety Data Sheets California Proposition 65 WarningsMATERIAL SAFETY DATA MATERIAL SAFETY DATA SHEETS MSDSWash hands after handling CALIFORNIA PROPOSITION 65 WARNINGSMATERIAL SAFETY DATA