PC Health Status | Gigabyte GA-K8NS manual

English

2-6	PC Health Status

		CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
			PC Health Status
	Vcore		OK			Item Help
	DDR25V		OK		Menu Level`
	+3.3V		OK
	+12V		OK
	Current CPU Temperature		36oC
	Current CPU FAN Speed		3245 RPM
	Current SYSTEM FAN Speed		0	RPM
	CPU Warning Temperature		[Disabled]
	CPU FAN Fail Warning		[Disabled]
	SYSTEM FAN Fail Warning		[Disabled]
KLJI: Move		Enter: Select	+/-/PU/PD: Value	F10: Save	ESC: Exit	F1: General Help
		F5: Previous Values		F7: Optimized Defaults

Current Voltage(V) Vcore / DDR25V / +3.3V / +12V

Detect system's voltage status automatically.

Current CPU Temperature

Detect CPU temperature automatically.

Current CPU/SYSTEM FAN Speed (RPM)

Detect CPU//SYSTEM Fan speed status automatically.

CPU Warning Temperature

60oC / 140oF	Monitor CPU temperature at 60oC / 140oF.
70oC / 158oF	Monitor CPU temperature at 70oC / 158oF.
80oC / 176oF	Monitor CPU temperature at 80oC / 176oF.
90oC / 194oF	Monitor CPU temperature at 90oC / 194oF.
Disabled	Disable this function. (Default value)

CPU/SYSTEM FAN Fail Warning

Disabled	Disable CPU/SYSTEM fan fail warning function. (Default value)
Enabled	Enable CPU/SYSTEM fan fail warning function.

GA-K8NS(rev. 2.0) Motherboard

- 40 -

Image 40

Gigabyte GA-K8NS user manual PC Health Status

Contents

GA-K8NSrev Motherboard Copyright Product Manual Classification Table of Contents Drivers Installation GA-K8NSrev .0 Motherboard Layout Block Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your Computer Feature Summary CPU Use of licensed Award Bios Installation of the CPU and Heatsink Installation of the CPU Installation of the Heatsink Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD Floppy Connector IDE1 / IDE2 IDE Connector SATA0SB / SATA1SB Serial ATA Connector Battery Fpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In Connector Surcen Surround Center Connector Spdifio Spdif In / Out Connector USB1 / FUSB2 Front USB Connector Clrcmos Clear Cmos English Status Page Setup Menu / Option Page Setup Menu Main Menu Main Menu For example Bios Ver. F13 „ Load Optimized Defaults „ Set Supervisor Password„ Set User Password „ Save & Exit Setup Standard Cmos Features TimeIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave IDE Channel 2/3 Master Drive a / Drive B Floppy 3 Mode Support for Japan AreaHalt on Advanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Boot Up Floppy Seek Password Check Init Display First Integrated Peripherals SPP On-Chip LAN Boot ROM IDE Channel 1 Slave RAIDSata Primary Master RAID Sata Secndry Master RAID Parallel Port Mode ECP Mode Use DMAOnboard Serial Port Onboard Parallel Port Power Management Setup Resume by AlarmPME Event Wake Up Modem Ring On Power On by Mouse Power On by KeyboardKB Power on Password AC Back Function PnP/PCI Configurations PCI 3 IRQ Assignment PC Health Status Frequency/Voltage Control Load Optimized Defaults Top Performance Set Supervisor/User Password Save & Exit Setup Exit Without Saving Drivers Installation Install Chipset Drivers Software Application Software Information Hardware Information Contact Us English EasyTune 5 Introduction Unique Software UtilitiesUser Interface Overview What is Xpress Recovery ? Xpress Recovery IntroductionHow to use the Xpress Recovery F9 For Xpress Recovery Press F9 during powering on the computer. Text Mode Remove Backup Image Remove backup image. Are you sure? Y/N Exit and Restart Method 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utility Using the Q-FlashTMutility Steps You can repeat to Part Two Exploring the Q-FlashTMutility screen English Congratulation!! You have updated Bios successfully Bios file becomes F4 after updating Method 2 @BIOSTM Utility Methods and steps English Serial ATA Bios Setting Utility Introduction RAID Levels Configuring the Nvidia RAID Bios Entering the RAID Bios Setup Using the Define a New Array Window Selecting the RAID ModeSelecting the Striping Block Size Assigning the Disks Completing the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Installing the RAID drivers Cd bootdrv Menu Stereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function Introduction Channel Audio Setup English English English Spdif Output Device Optional Device Jack-Sensing and UAJ Introduction Introduction of audio connectorsAuto-detecting Enable UAJ function Manual settingUAJ Introduction Troubleshooting English English Contact Us Taiwan Headquarters China Shanghai