Manuals / Gigabyte / Computer Equipment / Computer Hardware

Gigabyte P4 Titan-DDR Motherboard, GA-8ILFT user manual English

Models: GA-8ILFT P4 Titan-DDR Motherboard

1 77

Page 72

(4) The BIOS flash completed. Please press [ESC] to exit Flash Utility.

English

(3)It will pop up a screen and asks "Are you sure to flash the BIOS?" Press [Enter] to continue the procedure, or press [ESC] to quit.

Beware: Please do not turn off the system while you are upgrading BIOS. It will render your BIOS corrupted and system totally inoperative.

Are you sure to flash the BIOS? [Enter] tocontinue Or [Esc] to cancel?

(4) The BIOS flash completed. Please press [ESC] to exit Flash Utility.

EXIT?

[Enter] tocontinue Or [Esc] to cancel?

GA-8ILFT Series Motherboard

- 72 -

Page 72

Image 72

Gigabyte P4 Titan-DDR Motherboard, GA-8ILFT English, The BIOS flash completed. Please press ESC to exit Flash Utility

Contents

USER’S MANUAL GA-8ILFT Series P4 Titan-DDR MotherboardChapter 3 BIOS Setup EnglishTable of Content Chapter 4 Technical Reference Chapter 5 AppendixItem Checklist Installing the motherboard to the ch assis…English Features Summary Chapter 1 IntroductionEnglish For GA-8ILFT OnlyGA-8ILFT Series Motherboard Layout GA-8ILFTChapter 2 Hardware Installation Process Step 2- Install memory modulesStep 5- Install supporting software tools EnglishStep 1 Install the Central Processing Unit CPU Step 1-1 CPU InstallationPin1 indicator Pin1 indicatorStep 1-2 CPU Heat Sink Installation EnglishStep 2 Install memory modules Total Memory Sizes With Unbuffered DDR DIMMDDR 1. The DIMM slot has a notch, so the DIMMmemory module can only fit in one directionEnglish DDR IntroductionStep 3 Connect ribbon cables, cabinet wires, and power supply u PS/2 Keyboard and PS/2 Mouse ConnectorStep3-1 I/O Back Panel Introduction v Parallel Port and Serial Ports COM1/COM2x Audio Connectors y USB/LAN* ConnectorLA N* Connector EnglishPage B CPUFAN CPU FAN Connector F SYSFAN System FAN ConnectorA ATX12V +12V Power Connector Ø This 2 pin connector allows your system toD FDD Floppy Connector E IDE1/ IDE2 IDE1/IDE2 Conn ectorK FUSB 1 Front USB Co nnector QFAUDIO FAUDIO Connector EnglishN CDIN CD IN P SPDIF SPD IFC ATXPOWER ATX Power O SIRQ For special design, for example PCMCIA add on cardM AUXIN AUX In Connector L BATTERYBatteryv Danger of explosion if battery is incorrectly EnglishI FPANEL 2x7 pins connector Close Reset Hardware SystemRST+ SPK+Chapter 3 BIOS Setup ENTERING SETUPCONTROL KEYS EnglishStatus Page Setup Menu / Option Page Setup Menu Standard CMOS FeaturesAdvancedBIOS Features GETTING HELP MainMenuPowerManagementSetup PnP/PCI ConfigurationsLoadFail-Safe Defaults LoadOptimized DefaultsStandard CMOS Features C DateC Time C IDE Primary Master,Slave / IDE Secondary Master, SlaveC Drive A / Drive B EnglishC Floppy 3 Mode Support for Japan Area C HaltonC Memory BaseMemoryAdvanced BIOS Features C First / Second / Third Boot DeviceEnglish C Boot Up Floppy Seek C Init Display FirstC Graphics Aperture Size C GraphicsShare MemoryIntegrated Peripherals C On-Chip Primary PCIIDEEnglish C On-Chip Secondary PCI IDE C IDE1 Conductor CableC IDE2 Conductor Cable C USB ControllerC Onboard LANBootROM C UART Mode SelectC AC97 Audio C OnboardLANC UR2Duplex Mode C ParallelPort ModeC OnboardParallel port C ECPMode Use DMAC Midi Port IRQ Set Midi Port Address to 330.Default ValueSet Midi Port IRQ to 10. Default Value EnglishPower Management Setup C ACPI Suspend TypeC Soft-off by PWRBTTN C Resume by Alarm C Power On By MouseC Power OnBy Keyboard C KB Power ON PasswordPnP/PCI Configurations C PCI 1 IRQ AssignmentC PCI 2 IRQ Assignment C PCI 3 IRQ AssignmentC Reset Case Open Status C Case Opened PC Health StatusC Current Voltage V VCORE / 1.5V /+3.3V / +5V / +12V EnglishC Current CPUTemperature C CPUWarning TemperatureC Current CPU/SYSTEM FAN Speed RPM C CPU FAN Fail WarningFrequency/Voltage Control C CPU Clock RatioC CPU Host Clock Control C CPUHost FrequencyC PCI/AGPDivider C Host/DRAM ClockRatioC MemoryFrequencyMhz C PCI/AGP FrequencyMhzLoad Fail-Safe Defaults Load Fail-Safe D efaults? Y/N?YEnglish TopPerformanceLoad Optimized Defaults Load Optimized Defaults? Y/N?YLoadOptimized Defaults Set Supervisor/User Password EnglishSave & Exit Setup Save to CMOS and EXIT Y/N? YExit Without Saving Quit Without Saving Y/N? NEnglish Block Diagram RevisionChapter History4 Technical ReferenceQ-Flash Introduction A. What is Q-Flash Utility?B. How to use Q-Flash? EnglishLoad B IOS From F loppy @ BIOS Introduction Gigabyte announces @ BIOS Windows BIOS live update utilityEnglish Easy TuneTM 4 Introduction Gigabyte announces EasyTuneTM Windows based Overclocking utilityRevisionChapter History5 Appendix Englishj k l m A-1. Intel C hipset Software Installation Utility 2.Click Next3.Click Yes 4.Click NextEnglish 5.Click Finish to restart computerA-2. Intel Application Accelerator English 6.Click Finish to restart computerA-3. Intel 845G Chipset VGA Graphics Driver English A-4. USB Patch Driver4.Click Finish to restart computer 1.Click USB Patch Driver itemRevision History AppendixRevisionB RealTekHistoryAC’97 Audio DriverEnglish Appendix C RealTek 8139/8130/8100 Network DriverAppendixRevisionD EasyTuneHistory4 Utilities Installation Appendix E BIOS Flash Procedure EnglishII. Update BIOS NOT through Internet English Method3 After the floppy has been formatted completely, please press Close STEP 3 Download BIOS and BIOS utility program 2 From Support zone, click the Motherboards BIOS & DriversEnglish Page English 5 At this time the screen shows the following picture, please click Extract button to unzip the filesSTEP 4 Make sure the system will boot from the floppy disk English Save to CMOS and EXIT Y/N? YSTEP 5 BIOS flashing 4 The BIOS flash completed. Please press ESC to exit Flash Utility EnglishSTEP 6 LoadBIOS defaults Load Setup Defaults? Y/N?N4 Congratulate you have accomplished the BIOS flash procedure EnglishSave to CMOS and EXIT Y/N? Y Appendix E Acronyms Input Output Advanced Programmable Input ControllerEnglish Technical Support/RMA Sheet