Manuals / Graco / Personal Care / Microscope & Magnifier

Graco 333282B important safety instructions Personal Protective Equipment

Models: 333282B

1 76

Download 76 pages 38.62 Kb

Page 11

Warnings

WARNING

PERSONAL PROTECTIVE EQUIPMENT

Wear appropriate protective equipment when in the work area to help prevent serious injury, including eye injury, hearing loss, inhalation of toxic fumes, and burns. This protective equipment includes but is not limited to:

•Protective eyewear, and hearing protection.

•Respirators, protective clothing, and gloves as recommended by the ﬂuid and solvent manufacturer.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

•Do not operate the unit when fatigued or under the inﬂuence of drugs or alcohol.

•Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equipment manuals.

•Use ﬂuids and solvents that are compatible with equipment wetted parts. See Technical Data in all equipment manuals. Read ﬂuid and solvent manufacturer’s warnings. For complete information about your material, request MSDS from distributor or retailer.

•Do not leave the work area while equipment is energized or under pressure.

•Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.

•Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer’s replacement parts only.

•Do not alter or modify equipment. Alterations or modiﬁcations may void agency approvals and create safety hazards.

•Make sure all equipment is rated and approved for the environment in which you are using it.

•Use equipment only for its intended purpose. Call your distributor for information.

•Route hoses and cables away from trafﬁc areas, sharp edges, moving parts, and hot surfaces.

•Do not kink or over bend hoses or use hoses to pull equipment.

•Keep children and animals away from work area.

•Comply with all applicable safety regulations.

333282B

11

Image 11

Graco 333282B important safety instructions Personal Protective Equipment

Contents

Color Change and Remote Mix Manifold Kits Important Safety InstructionsContents Manual No Related ManualsManual No Description Non-Intrinsically Safe Modules ModelsControl Module Pressure Valves Number of Catalyst + Solvent Valves Intrinsically Safe ModulesKit Identiﬁcation Label 0359Models continue on next 333282B Models Fire and Explosion Hazard Intrinsic Safety Personal Protective Equipment Changing Materials Important Isocyanate ISO InformationIsocyanate Conditions Moisture Sensitivity of IsocyanatesModule Setup the ModulesSetup Non-IS Control Modules Color Change Control Modules, Colors, and CatalystsOutlet Manifold Non-IS Control Module Switch SettingsInlet Manifold Inlet Manifold Outlet Manifold Solenoid Valve Is Control Module Switch Settings Setup is Control ModulesIs Control Module Valve Solenoid Is Control Module Solenoid ValveGrounding InstallationMounting the Control Modules Air SupplyConnect the Color Change Control Modules Non-Hazardous LocationInstall the Valve Manifolds Install the Valve ManifoldsInstallation Connect Remote Color Change Control Module Hazardous LocationInstall the Remote Valve Manifolds Hazardous Area Install the Remote Mix ManifoldConnect the Valve Air Lines Non-Hazardous AreaInstallation Connect Non-Circulating Fluid Lines Valve Manifold Stack SchematicConnect the Fluid Lines KEY Valve Manifold Connections Circulating System Connect Circulating Fluid LinesKEY Install an Expansion Kit Install an Expansion Kit Low Pressure Valve Manifold Shown Color Change Solenoid Valves TroubleshootingCause Solution Replace the Color Change Board Fuse, Color Change Board Troubleshooting Power Module Electrical SchematicsEfcm Cable J8 J9 J15 J16 J14 J10 J15 J16 Electrical Schematic, Sheet 3, Hazardous Location Optional Cables and Modules Replace a Color Valve RepairFuse Description Replace a SolenoidReplace the Color Change Board Fuse Control Module Repair Non-IS Module Shown Replace the Color Change BoardNon-IS Color Change Kits PartsPart Description Qty Low Pressure Non-IS KitsHigh Pressure Circulating Color Change Kits High Pressure Non-IS KitsKit No Kit Description High Pressure Non-Circulating Color Change KitsParts Description Qty Is Color Change KitsAll available kits Parts Low Pressure is KitsHigh Pressure is Kits Circulating Valve Manifold Kits Kit No Valve Manifold KitsLow Pressure Valve Manifold Kits Non-Circulating Valve Manifold Kits Kit No SeriesValve Manifold Kit Parts Kit No Parts Low Pressure Circulating Valve Manifold Kit Part Quantities Circulating Valve Manifold Kits Kit No Series High Pressure Valve Manifold KitsValve Manifold Kit Parts 24T581 Parts High Pressure Circulating Valve Manifold Kit Part Quantities Parts Non-IS Color Change Control Modules Color Change Control Module KitsNon-IS Control Module Part Quantities Kit No Position Solenoid Plug Tie Strap Ferrule ConnectorConnector 310 321 322 Fitting 305 324 Is Color Change Control Modules Is Control Module Part Quantities 16M00Parts High Pressure Acid-Compatible Expansion Kits Expansion KitsNon-IS Expansion Kits Low Pressure Expansion Kits High Pressure Expansion KitsLow Pressure Expansion Kits Is Expansion KitsDimensions Manifold Mounting Bracket, Non-IS 11.44 312 Mm diameter Dimensions Dimensions Color Change Kits Metric Technical DataGraco Information Graco Standard Warranty