Manuals / Graco / Personal Care / Microscope & Magnifier

Graco 333282B Replace the Color Change Board, Control Module Repair Non-IS Module Shown

Models: 333282B

1 76

Download 76 pages 38.62 Kb

Page 45

Replace the Color Change Board

NOTICE

To avoid damaging the circuit boards, wear Part No. 112190 grounding strap on your wrist and ground appropriately.

To avoid electrical component damage, remove all system power before plugging any connectors.

1. Remove electrical power from the system.

Figure 23 Control Module Repair (Non-IS Module Shown)

Repair

2.Remove the color change module cover (304).

3.Note where each cable is connected, then disconnect all cables from the color change board connectors.

4.Remove the seven mounting screws (303) and the board (302).

5.Install the new board. Reinstall the screws.

6.Reconnect the cables to the proper connectors, as noted in step 3. See Electrical Schematics, page 36.

7.Reinstall the cover (304). Restore electrical power to the system.

333282B

45

Image 45

Graco 333282B important safety instructions Replace the Color Change Board, Control Module Repair Non-IS Module Shown

Contents

Color Change and Remote Mix Manifold Kits Important Safety InstructionsContents Related Manuals Manual No DescriptionManual No Non-Intrinsically Safe Modules ModelsControl Module Pressure Valves Kit Identiﬁcation Label Intrinsically Safe Modules0359 Number of Catalyst + Solvent ValvesModels continue on next 333282B Models Fire and Explosion Hazard Intrinsic Safety Personal Protective Equipment Isocyanate Conditions Important Isocyanate ISO InformationMoisture Sensitivity of Isocyanates Changing MaterialsSetup Non-IS Control Modules Setup the ModulesColor Change Control Modules, Colors, and Catalysts ModuleNon-IS Control Module Switch Settings Inlet ManifoldOutlet Manifold Inlet Manifold Outlet Manifold Solenoid Valve Is Control Module Switch Settings Setup is Control ModulesIs Control Module Valve Solenoid Is Control Module Solenoid ValveMounting the Control Modules InstallationAir Supply GroundingConnect the Color Change Control Modules Non-Hazardous LocationInstall the Valve Manifolds Install the Valve ManifoldsInstallation Connect Remote Color Change Control Module Hazardous LocationInstall the Remote Valve Manifolds Connect the Valve Air Lines Install the Remote Mix ManifoldNon-Hazardous Area Hazardous AreaInstallation Valve Manifold Stack Schematic Connect the Fluid LinesConnect Non-Circulating Fluid Lines KEY Valve Manifold Connections Circulating System Connect Circulating Fluid LinesKEY Install an Expansion Kit Install an Expansion Kit Low Pressure Valve Manifold Shown Troubleshooting Cause SolutionColor Change Solenoid Valves Replace the Color Change Board Fuse, Color Change Board Troubleshooting Power Module Electrical SchematicsEfcm Cable J8 J9 J15 J16 J14 J10 J15 J16 Electrical Schematic, Sheet 3, Hazardous Location Optional Cables and Modules Replace a Color Valve RepairReplace a Solenoid Replace the Color Change Board FuseFuse Description Control Module Repair Non-IS Module Shown Replace the Color Change BoardNon-IS Color Change Kits PartsPart Description Qty Low Pressure Non-IS KitsKit No Kit Description High Pressure Non-IS KitsHigh Pressure Non-Circulating Color Change Kits High Pressure Circulating Color Change KitsParts Description Qty Is Color Change KitsAll available kits Parts Low Pressure is KitsHigh Pressure is Kits Low Pressure Valve Manifold Kits Valve Manifold KitsNon-Circulating Valve Manifold Kits Kit No Series Circulating Valve Manifold Kits Kit NoValve Manifold Kit Parts Kit No Parts Low Pressure Circulating Valve Manifold Kit Part Quantities Circulating Valve Manifold Kits Kit No Series High Pressure Valve Manifold KitsValve Manifold Kit Parts 24T581 Parts High Pressure Circulating Valve Manifold Kit Part Quantities Parts Non-IS Color Change Control Modules Color Change Control Module KitsKit No Position Solenoid Plug Tie Strap Ferrule Connector Connector 310 321 322 Fitting 305 324Non-IS Control Module Part Quantities Is Color Change Control Modules Is Control Module Part Quantities 16M00Parts Non-IS Expansion Kits Expansion KitsLow Pressure Expansion Kits High Pressure Expansion Kits High Pressure Acid-Compatible Expansion KitsLow Pressure Expansion Kits Is Expansion KitsDimensions Manifold Mounting Bracket, Non-IS 11.44 312 Mm diameter Dimensions Dimensions Color Change Kits Metric Technical DataGraco Information Graco Standard Warranty