Manuals / Graco / Kitchen Appliance / Oven

Graco 3A0237L important safety instructions Connect Solenoid Kit, Connect Splitter

Models: 3A0237L

1 42

Download 42 pages 55.61 Kb

Page 21

Connect Solenoid Kit

Connect Solenoid Kit

A solenoid kit is required for some applicators used with Graco Metering Systems. See Individual Hoses on page 5 to see which applicators require a solenoid kit.

NOTE: To ensure proper operation of valve, install the solenoid kit within 15 ft (4.5 m) of the applicator. The solenoid reaction time decreases if the solenoid kit is farther away from the applicator. Ensure that the scuff guard covers the solenoid if mounted between the hose and whip hose.

1.Turn off all power to the system.

2.Apply anaerobic pipe sealant to pipe threads on mufflers (205), tee fitting (202), and swivel fitting

(215). Connect to valve (201).

3.Connect elbow fittings (204), and wire harness

(206)to valve (201).

4.Connect air hose (C) to swivel fitting (215).

5.Connect two elbows (207) and tubing (212) to open and closed ports on the applicator. See applicator manual for port locations.

NOTE: Cut tubing (212) to desired length if neces- sary.

206

207

205

212

202

204

215 205

201

r_24D161_3a0237b_1b

C

FIG. 14

Installation

6.Install plug (203), or tube fitting (214) and ball valve (213) in the other side of the tee fitting (202).

213202

207 212 214

203 r_24D161_3a0237B_2b

FIG. 15

7.For solenoid kit 24D161: Connect elbow fitting (207) and tubing (212) to the purge air port and tube fitting (214). See applicator manual for port locations.

Connect Splitter

24D160 and 24D161 use a splitter (211) to allow the Graco Metering System to dispense material from the system controls.

1.Connect the splitter (211) to the valve (201) with screw (208), washer (209), and nut (210).

2.Connect the hose communications cable (24) to the single splitter (211) connection.

3.Connect the wire harness (206) and signal cable (3b) from the whip hose to the splitter (211).

206 3b

208 210

209

201 211

24

r_24D160_3a0237b_1b

FIG. 16

3A0237L

21

Image 21

Graco 3A0237L Connect Solenoid Kit, Connect Splitter, NOTE Cut tubing 212 to desired length if neces- sary

Contents

For use with Graco HFR Metering Systems Important Safety InstructionsHeated Hoses and Applicator KitsRelated Manuals ContentsManual DescriptionAll heated hose bundles are CE approved Heated Hose Bundle Part NumbersHeated Hose Bundle Part Numbers 3A0237LHeated Whip Hose Fluid Temperature Sensor FTSFittings Heated Hose Bundle Part NumbersA Side Heated Hoses Red Individual HosesIndividual Hoses 3A0237LA Side Unheated Hoses Red Individual A Side Heated Whip HoseIndividual Hoses All heated hoses are CE approved B Side Heated Hoses BlueIndividual Hoses 3A0237LB Side Unheated Hoses Blue Individual B Side Heated Whip HoseIndividual Hoses Applicator Applicator KitsHandle Options Required Solenoid KitMD2 Handle MD2 Valve Applicator KitsChemical Connection Kit see manualELECTRIC SHOCK HAZARD WarningsSKIN INJECTION HAZARD THERMAL EXPANSION HAZARDTOXIC FLUID OR FUMES HAZARD FIRE AND EXPLOSION HAZARDEQUIPMENT MISUSE HAZARD PERSONAL PROTECTIVE EQUIPMENT Isocyanate Conditions Important Two-Component Material InformationMaterial Self-ignition Keep Components A and B SeparateChanging Materials A and B ComponentsDescription InstallationConnect Whip Hose to Gun or Gun Manifold NOTE Use chemical connection kit 153 on all MD2 valves. See FIGSingle Heat Zone with A and B Heated Hose Connect Heated HosesDual Heat Zone with A and B Heated Hose Single Heat Zone with A or B Heated HoseFIG. 9 Insert Wire and Setscrew Incorrect Correct IncorrectFIG. 10 Torque Setscrew Cap plugs Setscrews 9. See Connect FTS and Heated Whip Hose, page1. For Single Zone Heat Connect FTS and Heated Whip HoseFor Dual Zone Heat Single Zone HeatConnect Solenoid Kit Connect SplitterNOTE Cut tubing 212 to desired length if neces- sary Protective Covering Check Hoses for LeaksSingle Heat Zone Shown OperationClean Orifice Maintenance1. Follow Pressure Relief Procedure in MD2 valve manual Instructions for Replacing Individual A or B Hose3A0237L MaintenanceNOTE Ensure no foam insulation is exposed on either material hose Bundle Individual Whip HosesSingle Heat Zone Heated Whip Hose Bundle Dual Heat Zone Heated Whip Hose BundleB Side A Sidethe material hose Bundle Individual Heated HosesNOTE Do not twist 5 ft and 10 ft hose bundle lengths NOTE Ensure no foam insulation is exposed on either material hoseMachine End Dual Heat Zone Heated Hose Bundle ShownFIG. 22 Heated Hose Bundles MaintenanceWhip Hoses PartsDual Heat Zone Heated Whip Hose Single Heat Zone Heated Whip HoseHeated Whip Hoses Air Hose and Signal Cable KitsCommon Parts Part No. DescriptionDual Heat Zone Heated Hose Bundle Shown Heated Hose BundlesMachine End A SideCommon Parts Dual Zone Heated Hose BundlesPart No. Description Varied PartsCommon Parts Single Zone Heated Hose BundlesPart No. Description Varied PartsUsing Fluid Temperature Sensors for Dual Heat Zones Using Fluid Temperature Sensors For Single Heat Zones258758 Carbon Steel Fluid Temperature Sensor 258757 Stainless Steel Fluid Temperature SensorPart 15F144 Hose Wire JumperConnect 258758 , page DescriptionMD2 Applicator Kits MD2 Applicator Kits153 24D162 Stainless Steel Connection Kit 24E505 Orifice Block KitScuff Guard AccessoriesSolenoid Kits 24C757 Machine Mount KitOnly 24D161 24D160 Remote Mount MD2 Kit 24D161 Remote Mount Fusion KitOnly 24D160 PartTechnical Data CategoryData 3A0237L Technical DataGraco Information Graco Standard WarrantyGraco Headquarters Minneapolis Graco reserves the right to make changes at any time without notice