Manuals / Graco / Kitchen Appliance / Oven

Graco 3A0237L See Connect FTS and Heated Whip Hose, page, Cap plugs Setscrews

Models: 3A0237L

1 42

Download 42 pages 55.61 Kb

Page 19

Image 19

Installation

f.Insert cap plugs over setscrews. See FIG. 11.

Cap plugs

Setscrews

TI9771A

FIG. 11

g.Wrap connector and wire on each side of con- nector in black electrical tape to help seal out moisture. Ensure 1 in. (25.4 mm) of wire on each side of connector is wrapped.

7.Connect cables (F). Leave slack (G) in cables as stress relief to prevent cable failure.

FIG. 12

TI14734a

8.Repeat for additional hoses.

9.See Connect FTS and Heated Whip Hose, page 20.

3A0237L

Page 19

Image 19

Graco 3A0237L important safety instructions See Connect FTS and Heated Whip Hose, page, Cap plugs Setscrews

Contents

Applicator Kits Important Safety InstructionsFor use with Graco HFR Metering Systems Heated Hoses andDescription ContentsRelated Manuals Manual3A0237L Heated Hose Bundle Part NumbersAll heated hose bundles are CE approved Heated Hose Bundle Part NumbersHeated Hose Bundle Part Numbers Fluid Temperature Sensor FTSHeated Whip Hose Fittings3A0237L Individual HosesA Side Heated Hoses Red Individual HosesIndividual A Side Heated Whip Hose A Side Unheated Hoses RedIndividual Hoses 3A0237L B Side Heated Hoses BlueAll heated hoses are CE approved Individual HosesIndividual B Side Heated Whip Hose B Side Unheated Hoses BlueIndividual Hoses Required Solenoid Kit Applicator KitsApplicator Handle Optionssee manual MD2 Valve Applicator KitsMD2 Handle Chemical Connection KitTHERMAL EXPANSION HAZARD WarningsELECTRIC SHOCK HAZARD SKIN INJECTION HAZARDFIRE AND EXPLOSION HAZARD TOXIC FLUID OR FUMES HAZARDEQUIPMENT MISUSE HAZARD PERSONAL PROTECTIVE EQUIPMENT Keep Components A and B Separate Important Two-Component Material InformationIsocyanate Conditions Material Self-ignitionChanging Materials A and B ComponentsNOTE Use chemical connection kit 153 on all MD2 valves. See FIG InstallationDescription Connect Whip Hose to Gun or Gun ManifoldSingle Heat Zone with A or B Heated Hose Connect Heated HosesSingle Heat Zone with A and B Heated Hose Dual Heat Zone with A and B Heated HoseIncorrect Correct Incorrect FIG. 9 Insert Wire and SetscrewFIG. 10 Torque Setscrew Cap plugs Setscrews 9. See Connect FTS and Heated Whip Hose, pageSingle Zone Heat Connect FTS and Heated Whip Hose1. For Single Zone Heat For Dual Zone HeatConnect Splitter Connect Solenoid KitNOTE Cut tubing 212 to desired length if neces- sary Protective Covering Check Hoses for LeaksSingle Heat Zone Shown OperationInstructions for Replacing Individual A or B Hose MaintenanceClean Orifice 1. Follow Pressure Relief Procedure in MD2 valve manual3A0237L MaintenanceNOTE Ensure no foam insulation is exposed on either material hose Bundle Individual Whip HosesA Side Dual Heat Zone Heated Whip Hose BundleSingle Heat Zone Heated Whip Hose Bundle B SideNOTE Ensure no foam insulation is exposed on either material hose Bundle Individual Heated Hosesthe material hose NOTE Do not twist 5 ft and 10 ft hose bundle lengthsMaintenance Dual Heat Zone Heated Hose Bundle ShownMachine End FIG. 22 Heated Hose BundlesSingle Heat Zone Heated Whip Hose PartsWhip Hoses Dual Heat Zone Heated Whip HosePart No. Description Air Hose and Signal Cable KitsHeated Whip Hoses Common PartsA Side Heated Hose BundlesDual Heat Zone Heated Hose Bundle Shown Machine EndVaried Parts Dual Zone Heated Hose BundlesCommon Parts Part No. DescriptionVaried Parts Single Zone Heated Hose BundlesCommon Parts Part No. Description258757 Stainless Steel Fluid Temperature Sensor Using Fluid Temperature Sensors For Single Heat ZonesUsing Fluid Temperature Sensors for Dual Heat Zones 258758 Carbon Steel Fluid Temperature SensorDescription 15F144 Hose Wire JumperPart Connect 258758 , page24E505 Orifice Block Kit MD2 Applicator KitsMD2 Applicator Kits 153 24D162 Stainless Steel Connection Kit24C757 Machine Mount Kit AccessoriesScuff Guard Solenoid KitsPart 24D160 Remote Mount MD2 Kit 24D161 Remote Mount Fusion KitOnly 24D161 Only 24D160Category Technical DataData 3A0237L Technical DataGraco reserves the right to make changes at any time without notice Graco Standard WarrantyGraco Information Graco Headquarters Minneapolis