Manuals / Graco / Power Tools / Paint Sprayer

Graco ti13585a, ti13586a Mount Gun, Reciprocating Arm Rod Mount, Stationary Support

Models: ti13585a

1 44

Download 44 pages 28.69 Kb

Page 12

Image 12

Installation

Mount Gun

Reciprocating Arm Rod Mount

To mount the gun on a reciprocating arm rod

[0.5 in. (13 mm) diameter maximum]:

1.Insert the mounting bar (A) through the hole in the manifold as shown in FIG. 3.

NOTE: Use the 1/8 in. alignment pin (P) to assist in orienting the gun.

2.Secure the gun to the bar by tightening the mounting screw (B).

ti13587a

FIG. 3: Reciprocating Arm Mount

Stationary Support

To mount the gun on a stationary support (refer to FIG. 4 and to the correct mounting hole layout for your manifold, pages 38-42):

1.Align the manifold with the alignment pins. Locate alignment pins and holes per the mounting hole layout.

2.Secure the gun to the support with two M5 x 0.8 capscrews (C). The screws must be long enough to engage the threaded holes in the gun manifold to a depth of 1/4 in.

(6 mm).

ti13588a

FIG. 4: Stationary Support Mount

313516G

Page 12

Image 12

Graco ti13585a, ti13586a important safety instructions Mount Gun, Reciprocating Arm Rod Mount, Stationary Support

Contents

Important Safety Instructions Automatic AirPro Spray GunsInstructions-Parts 313516GContents ModelsApplication Orifice SizeWarnings FIRE AND EXPLOSION HAZARDEQUIPMENT MISUSE HAZARD PRESSURIZED EQUIPMENT HAZARD TOXIC FLUID OR FUMES HAZARDPERSONAL PROTECTIVE EQUIPMENT Selection Charts General Metal ApplicationsTERMS With Fluid Control Knob for fine adjustment of fluid flowHigh Wear Applications Wood ApplicationsGun Selection HVLP GunsProper Needle/Nozzle Selection Air CapsConventional Guns Air Flow Atomizing AirFan Air Atomizing Air Fan AirMaximum HVLP/Compliant inlet manifold pressure Installation Ventilate Spray BoothConfigure Gun and Manifold Circulating SystemInstall Air Fittings Ground Air Compressors and Hydraulic Power SuppliesGround System Ground Spray GunMount Gun Reciprocating Arm Rod MountStationary Support Retrofit Adapter Plate FIG. 5 Retrofit Adapter Plate MountSetup Connect Air LineConnect Fluid Hose Flush Spray Gun Position Air CapSide Mounted Manifold Ports Bottom Mounted Manifold PortsAdjust Spray Pattern Table 1 Suggested Starting SettingsAtomization Fan Air psiNOTE HVLP and Compliant Gun Limits Pressure Relief Procedure OperationApply Fluid IncorrectDaily Gun Care General System Maintenance Clean and Flush GunTroubleshooting General TroubleshootingProblem SolutionSpray Pattern Troubleshooting ProblemSolution ProblemService Disassembly14. Perform the following applicable step Reassembly Parts Partsti13593b Included in Air Seal Repair Kit † Included in Fluid Seal Repair Kit 24B675 Not sold separatelyRepair Kits General Metal ApplicationsOrifice SizeHigh Wear Applications Wood ApplicationsModel has Fluid Control Knob for fine adjustment of fluid flow Needle tip and nozzle exit constructed from tungsten carbideManifold with bottom fluid ports 114101 103 107 105108Not shown Not sold separately Part No. 24C342 Not shown, optional size Not sold separately Part No. 288223 onlyPart No. 24C342 only North America Manifold with side fluid ports International Manifold with side fluid ports107 101 114 103 Not shown, optional size Not sold separately Part No. 288217 onlyNot shown, optional size Not sold separately Part No. 288160 only Part No. 288211 only2 Torque to 8-10 in-lb 0.9-1.3 Nm 3 Torque to 110-130 in-lb 12.3-4.7 NmAccessories Cleaning BrushReplacement Gun 24A780 Alternate Nozzle SizesHVLP Pressure Verification Kit Inline Fluid Filter 24B707Spray Tip Filters TipsDimensions Manifold Models 288217 or 288218, All Gun ModelsManifold Model 288221, All Gun Models Manifold Model 288223 or 24C342, All Gun Models Manifold Model 288160 or 288211, All Gun ModelsMounting Hole Layouts Manifold Models 288217 or 288218, All Gun ModelsTwo M5 x 0.8 x 0.25 in. 6.3 mm holes Two 0.13 diameter 0.31 in. 7.8 mm holes. Use 1/8 in. pinManifold Model 288221, All Gun Models Two M5 x 0.8 x 0.25 in. 6.3 mm holesTwo 0.13 diameter 0.31 in. 7.8 mm holes. Use 1/8 in. pin for alignmentManifold Model 288223 or 24C342, All Gun Models 6.3 mm holesMounting Hole Layouts Four M6 x 1.0 x 0.34 inManifold Model 288160 or 288211, All Gun Models Two M5 x 0.8 x 0.25 in. 6.3 mm holesTwo 0.13 diameter 0.31 in. 7.8 mm holes. Use 1/8 in. pin for alignmentRetrofit Adapter Plate 2.3 in 57.7 mmMounting Hole Layouts ti8178aTechnical Data Triggering SpeedSound Data Cylinder AirGraco Standard Warranty Graco Information