Manuals / Graco / Power Tools / Paint Sprayer

Graco ti13586a Manifold Model 288221, All Gun Models, Two M5 x 0.8 x 0.25 in. 6.3 mm holes

Models: ti13585a

1 44

Download 44 pages 28.69 Kb

Page 39

Image 39

Manifold Model 288221, All Gun Models

0.92 in.

0.4 in.

0.18 in.

(23.4 mm)

(10.2 mm)

(4.6 mm)

2.1 in.

(53.3 mm)

0.50 in. (12.7 mm) mounting hole

Mounting Hole Layouts

Two M5 x 0.8 x 0.25 in. (6.3 mm) holes

1.75in. (44.4 mm)

1.375 in.

(34.9 mm)

Two 0.13 diameter x

0.31in. (7.8 mm) holes. Use 1/8 in. pin

for alignment

ti13888a

2.8 in.

(71.1 mm)

ti13881a

FIG. 32

313516G

Page 39

Image 39

Graco ti13586a Manifold Model 288221, All Gun Models, Two M5 x 0.8 x 0.25 in. 6.3 mm holes, for alignment, ti13888a

Contents

313516G Important Safety InstructionsAutomatic AirPro Spray Guns Instructions-PartsOrifice Size ContentsModels ApplicationWarnings FIRE AND EXPLOSION HAZARDEQUIPMENT MISUSE HAZARD PRESSURIZED EQUIPMENT HAZARD TOXIC FLUID OR FUMES HAZARDPERSONAL PROTECTIVE EQUIPMENT With Fluid Control Knob for fine adjustment of fluid flow Selection ChartsGeneral Metal Applications TERMSHVLP Guns High Wear ApplicationsWood Applications Gun SelectionProper Needle/Nozzle Selection Air CapsConventional Guns Air Flow Atomizing AirFan Air Atomizing Air Fan AirMaximum HVLP/Compliant inlet manifold pressure Circulating System InstallationVentilate Spray Booth Configure Gun and ManifoldGround Spray Gun Install Air FittingsGround Air Compressors and Hydraulic Power Supplies Ground SystemMount Gun Reciprocating Arm Rod MountStationary Support FIG. 5 Retrofit Adapter Plate Mount Retrofit Adapter PlateSetup Connect Air LineConnect Fluid Hose Bottom Mounted Manifold Ports Flush Spray GunPosition Air Cap Side Mounted Manifold PortsFan Air psi Adjust Spray PatternTable 1 Suggested Starting Settings AtomizationNOTE HVLP and Compliant Gun Limits Incorrect Pressure Relief ProcedureOperation Apply FluidDaily Gun Care Clean and Flush Gun General System MaintenanceSolution TroubleshootingGeneral Troubleshooting ProblemProblem Spray Pattern TroubleshootingProblem SolutionDisassembly Service14. Perform the following applicable step Reassembly Parts Partsti13593b † Included in Fluid Seal Repair Kit 24B675 Not sold separately Included in Air Seal Repair KitSize Repair KitsGeneral Metal Applications OrificeNeedle tip and nozzle exit constructed from tungsten carbide High Wear ApplicationsWood Applications Model has Fluid Control Knob for fine adjustment of fluid flowManifold with bottom fluid ports 114101 103 107 105108Not shown Not sold separately Part No. 24C342 Not shown, optional size Not sold separately Part No. 288223 onlyPart No. 24C342 only Not shown, optional size Not sold separately Part No. 288217 only North America Manifold with side fluid portsInternational Manifold with side fluid ports 107 101 114 1033 Torque to 110-130 in-lb 12.3-4.7 Nm Not shown, optional size Not sold separately Part No. 288160 onlyPart No. 288211 only 2 Torque to 8-10 in-lb 0.9-1.3 NmAlternate Nozzle Sizes AccessoriesCleaning Brush Replacement Gun 24A780Tips HVLP Pressure Verification KitInline Fluid Filter 24B707 Spray Tip FiltersDimensions Manifold Models 288217 or 288218, All Gun ModelsManifold Model 288221, All Gun Models Manifold Model 288160 or 288211, All Gun Models Manifold Model 288223 or 24C342, All Gun ModelsTwo 0.13 diameter 0.31 in. 7.8 mm holes. Use 1/8 in. pin Mounting Hole LayoutsManifold Models 288217 or 288218, All Gun Models Two M5 x 0.8 x 0.25 in. 6.3 mm holesfor alignment Manifold Model 288221, All Gun ModelsTwo M5 x 0.8 x 0.25 in. 6.3 mm holes Two 0.13 diameter 0.31 in. 7.8 mm holes. Use 1/8 in. pinFour M6 x 1.0 x 0.34 in Manifold Model 288223 or 24C342, All Gun Models6.3 mm holes Mounting Hole Layoutsfor alignment Manifold Model 288160 or 288211, All Gun ModelsTwo M5 x 0.8 x 0.25 in. 6.3 mm holes Two 0.13 diameter 0.31 in. 7.8 mm holes. Use 1/8 in. pinti8178a Retrofit Adapter Plate2.3 in 57.7 mm Mounting Hole LayoutsCylinder Air Technical DataTriggering Speed Sound DataGraco Information Graco Standard Warranty