Manuals / Graco / Power Tools / Paint Sprayer

Graco ti13586a HVLP Pressure Verification Kit, Inline Fluid Filter 24B707, Spray Tip Filters

Models: ti13585a

1 44

Download 44 pages 28.69 Kb

Page 35

HVLP Pressure Verification Kit

HVLP Pressure Verification Kit

For use in checking air cap atomizing and fan pattern air pressure at various supply air pres- sures. Not to be used for actual spraying.

Install the kit air cap on the gun. Turn on the air to the gun, then trigger the gun and read the air pressure on the gauge.

NOTE: To be “HVLP compliant,” the atomizing and fan pattern air pressure must not exceed 10 psi (70 kPa, 0.7 bar).

Part No.	Description

289563	HVLP General Metal

289568	HVLP High Wear 0.059 in. (1.5 mm)

289569	HVLP High Wear 0.070 in. (1.8 mm)

289566	HVLP Wood

ti13594a

FIG. 26: HVLP Pressure Verification Kit

Accessories

Inline Fluid Filter 24B707

Filter is removable without disconnecting the fluid line. Includes housing, o-ring, and

0.005 in. tip filter (equivalent to 100 mesh screen).

Spray Tip Filters

Final filter to prevent foreign particles from ruining sprayed surface smoothness.

25-Count
Carton	3-Pack	Description

238562	238561	0.005 in. (equivalent to 100
		mesh screen)

238564	238563	0.009 in. (equivalent to 60
		mesh screen)

Tips

Part No. Description

24E484 0.030 in. SST Needle Tips (Pack of 5)

313516G

35

Image 35

Graco ti13586a, ti13585a HVLP Pressure Verification Kit, Inline Fluid Filter 24B707, Spray Tip Filters, Tips

Contents

313516G Important Safety InstructionsAutomatic AirPro Spray Guns Instructions-PartsOrifice Size ContentsModels ApplicationEQUIPMENT MISUSE HAZARD WarningsFIRE AND EXPLOSION HAZARD PERSONAL PROTECTIVE EQUIPMENT PRESSURIZED EQUIPMENT HAZARDTOXIC FLUID OR FUMES HAZARD With Fluid Control Knob for fine adjustment of fluid flow Selection ChartsGeneral Metal Applications TERMSHVLP Guns High Wear ApplicationsWood Applications Gun SelectionConventional Guns Proper Needle/Nozzle SelectionAir Caps Fan Air Air FlowAtomizing Air Maximum HVLP/Compliant inlet manifold pressure Atomizing AirFan Air Circulating System InstallationVentilate Spray Booth Configure Gun and ManifoldGround Spray Gun Install Air FittingsGround Air Compressors and Hydraulic Power Supplies Ground SystemStationary Support Mount GunReciprocating Arm Rod Mount FIG. 5 Retrofit Adapter Plate Mount Retrofit Adapter PlateConnect Fluid Hose SetupConnect Air Line Bottom Mounted Manifold Ports Flush Spray GunPosition Air Cap Side Mounted Manifold PortsFan Air psi Adjust Spray PatternTable 1 Suggested Starting Settings AtomizationNOTE HVLP and Compliant Gun Limits Incorrect Pressure Relief ProcedureOperation Apply FluidDaily Gun Care Clean and Flush Gun General System MaintenanceSolution TroubleshootingGeneral Troubleshooting ProblemProblem Spray Pattern TroubleshootingProblem SolutionDisassembly Service14. Perform the following applicable step Reassembly ti13593b PartsParts † Included in Fluid Seal Repair Kit 24B675 Not sold separately Included in Air Seal Repair KitSize Repair KitsGeneral Metal Applications OrificeNeedle tip and nozzle exit constructed from tungsten carbide High Wear ApplicationsWood Applications Model has Fluid Control Knob for fine adjustment of fluid flowNot shown Not sold separately Manifold with bottom fluid ports114101 103 107 105108 Part No. 24C342 only Part No. 24C342Not shown, optional size Not sold separately Part No. 288223 only Not shown, optional size Not sold separately Part No. 288217 only North America Manifold with side fluid portsInternational Manifold with side fluid ports 107 101 114 1033 Torque to 110-130 in-lb 12.3-4.7 Nm Not shown, optional size Not sold separately Part No. 288160 onlyPart No. 288211 only 2 Torque to 8-10 in-lb 0.9-1.3 NmAlternate Nozzle Sizes AccessoriesCleaning Brush Replacement Gun 24A780Tips HVLP Pressure Verification KitInline Fluid Filter 24B707 Spray Tip FiltersManifold Model 288221, All Gun Models DimensionsManifold Models 288217 or 288218, All Gun Models Manifold Model 288160 or 288211, All Gun Models Manifold Model 288223 or 24C342, All Gun ModelsTwo 0.13 diameter 0.31 in. 7.8 mm holes. Use 1/8 in. pin Mounting Hole LayoutsManifold Models 288217 or 288218, All Gun Models Two M5 x 0.8 x 0.25 in. 6.3 mm holesfor alignment Manifold Model 288221, All Gun ModelsTwo M5 x 0.8 x 0.25 in. 6.3 mm holes Two 0.13 diameter 0.31 in. 7.8 mm holes. Use 1/8 in. pinFour M6 x 1.0 x 0.34 in Manifold Model 288223 or 24C342, All Gun Models6.3 mm holes Mounting Hole Layoutsfor alignment Manifold Model 288160 or 288211, All Gun ModelsTwo M5 x 0.8 x 0.25 in. 6.3 mm holes Two 0.13 diameter 0.31 in. 7.8 mm holes. Use 1/8 in. pinti8178a Retrofit Adapter Plate2.3 in 57.7 mm Mounting Hole LayoutsCylinder Air Technical DataTriggering Speed Sound DataGraco Information Graco Standard Warranty