Manuals / Graco / Power Tools / Paint Sprayer

Graco ti13586a Manifold Model 288160 or 288211, All Gun Models, for alignment, ti13890a, ti13885a

Models: ti13585a

1 44

Download 44 pages 28.69 Kb

Page 41

Image 41

Mounting Hole Layouts

Manifold Model 288160 or 288211, All Gun Models

Two M5 x 0.8 x 0.25 in. (6.3 mm) holes

0.92 in.	0.4 in.
(23.4 mm)	(10.2 mm)

0.19 in. (4.8mm)

1.1 in.

(27.9 mm)

0.375 in. (9.5 mm)

mounting hole

1.75 in.

1.375 in. (44.4 mm

(34.9 mm

Two 0.13 diameter x

0.31in. (7.8 mm) holes. Use 1/8 in. pin

for alignment

ti13890a

2.3 in.

(58.4 mm)

ti13885a

FIG. 34

313516G

Page 41

Image 41

Graco ti13586a Manifold Model 288160 or 288211, All Gun Models, Two M5 x 0.8 x 0.25 in. 6.3 mm holes, for alignment

Contents

Automatic AirPro Spray Guns Important Safety InstructionsInstructions-Parts 313516GModels ContentsApplication Orifice SizeEQUIPMENT MISUSE HAZARD WarningsFIRE AND EXPLOSION HAZARD PERSONAL PROTECTIVE EQUIPMENT PRESSURIZED EQUIPMENT HAZARDTOXIC FLUID OR FUMES HAZARD General Metal Applications Selection ChartsTERMS With Fluid Control Knob for fine adjustment of fluid flowWood Applications High Wear ApplicationsGun Selection HVLP GunsConventional Guns Proper Needle/Nozzle SelectionAir Caps Fan Air Air FlowAtomizing Air Maximum HVLP/Compliant inlet manifold pressure Atomizing AirFan Air Ventilate Spray Booth InstallationConfigure Gun and Manifold Circulating SystemGround Air Compressors and Hydraulic Power Supplies Install Air FittingsGround System Ground Spray GunStationary Support Mount GunReciprocating Arm Rod Mount FIG. 5 Retrofit Adapter Plate Mount Retrofit Adapter PlateConnect Fluid Hose SetupConnect Air Line Position Air Cap Flush Spray GunSide Mounted Manifold Ports Bottom Mounted Manifold PortsTable 1 Suggested Starting Settings Adjust Spray PatternAtomization Fan Air psiNOTE HVLP and Compliant Gun Limits Operation Pressure Relief ProcedureApply Fluid IncorrectDaily Gun Care Clean and Flush Gun General System MaintenanceGeneral Troubleshooting TroubleshootingProblem SolutionProblem Spray Pattern TroubleshootingSolution ProblemDisassembly Service14. Perform the following applicable step Reassembly ti13593b PartsParts † Included in Fluid Seal Repair Kit 24B675 Not sold separately Included in Air Seal Repair KitGeneral Metal Applications Repair KitsOrifice SizeWood Applications High Wear ApplicationsModel has Fluid Control Knob for fine adjustment of fluid flow Needle tip and nozzle exit constructed from tungsten carbideNot shown Not sold separately Manifold with bottom fluid ports114101 103 107 105108 Part No. 24C342 only Part No. 24C342Not shown, optional size Not sold separately Part No. 288223 only International Manifold with side fluid ports North America Manifold with side fluid ports107 101 114 103 Not shown, optional size Not sold separately Part No. 288217 onlyPart No. 288211 only Not shown, optional size Not sold separately Part No. 288160 only2 Torque to 8-10 in-lb 0.9-1.3 Nm 3 Torque to 110-130 in-lb 12.3-4.7 NmCleaning Brush AccessoriesReplacement Gun 24A780 Alternate Nozzle SizesInline Fluid Filter 24B707 HVLP Pressure Verification KitSpray Tip Filters TipsManifold Model 288221, All Gun Models DimensionsManifold Models 288217 or 288218, All Gun Models Manifold Model 288160 or 288211, All Gun Models Manifold Model 288223 or 24C342, All Gun ModelsManifold Models 288217 or 288218, All Gun Models Mounting Hole LayoutsTwo M5 x 0.8 x 0.25 in. 6.3 mm holes Two 0.13 diameter 0.31 in. 7.8 mm holes. Use 1/8 in. pinTwo M5 x 0.8 x 0.25 in. 6.3 mm holes Manifold Model 288221, All Gun ModelsTwo 0.13 diameter 0.31 in. 7.8 mm holes. Use 1/8 in. pin for alignment6.3 mm holes Manifold Model 288223 or 24C342, All Gun ModelsMounting Hole Layouts Four M6 x 1.0 x 0.34 inTwo M5 x 0.8 x 0.25 in. 6.3 mm holes Manifold Model 288160 or 288211, All Gun ModelsTwo 0.13 diameter 0.31 in. 7.8 mm holes. Use 1/8 in. pin for alignment2.3 in 57.7 mm Retrofit Adapter PlateMounting Hole Layouts ti8178aTriggering Speed Technical DataSound Data Cylinder AirGraco Information Graco Standard Warranty