Manuals / Graco / Power Tools / Paint Sprayer

Graco ti13585a Retrofit Adapter Plate, 2.3 in 57.7 mm, Mounting Hole Layouts, ti8178a, ti13600a

Models: ti13585a

1 44

Download 44 pages 28.69 Kb

Page 42

Image 42

Mounting Hole Layouts

Retrofit Adapter Plate 288197

For use with manifold models 288217, 288218, 288221, 288216, and 288211

2.0 in.

(51 mm)

1.4in.

(34.9 mm)

0.74 in.

(18.7 mm)

ti8178a

2.3 in.

(57.7 mm)

ti13600a

FIG. 35

313516G

Page 42

Image 42

Graco ti13585a, ti13586a Retrofit Adapter Plate, 2.3 in 57.7 mm, Mounting Hole Layouts, ti8178a, ti13600a, 313516G

Contents

Instructions-Parts Important Safety InstructionsAutomatic AirPro Spray Guns 313516GApplication ContentsModels Orifice SizeWarnings FIRE AND EXPLOSION HAZARDEQUIPMENT MISUSE HAZARD PRESSURIZED EQUIPMENT HAZARD TOXIC FLUID OR FUMES HAZARDPERSONAL PROTECTIVE EQUIPMENT TERMS Selection ChartsGeneral Metal Applications With Fluid Control Knob for fine adjustment of fluid flowGun Selection High Wear ApplicationsWood Applications HVLP GunsProper Needle/Nozzle Selection Air CapsConventional Guns Air Flow Atomizing AirFan Air Atomizing Air Fan AirMaximum HVLP/Compliant inlet manifold pressure Configure Gun and Manifold InstallationVentilate Spray Booth Circulating SystemGround System Install Air FittingsGround Air Compressors and Hydraulic Power Supplies Ground Spray GunMount Gun Reciprocating Arm Rod MountStationary Support Retrofit Adapter Plate FIG. 5 Retrofit Adapter Plate MountSetup Connect Air LineConnect Fluid Hose Side Mounted Manifold Ports Flush Spray GunPosition Air Cap Bottom Mounted Manifold PortsAtomization Adjust Spray PatternTable 1 Suggested Starting Settings Fan Air psiNOTE HVLP and Compliant Gun Limits Apply Fluid Pressure Relief ProcedureOperation IncorrectDaily Gun Care General System Maintenance Clean and Flush GunProblem TroubleshootingGeneral Troubleshooting SolutionSolution Spray Pattern TroubleshootingProblem ProblemService Disassembly14. Perform the following applicable step Reassembly Parts Partsti13593b Included in Air Seal Repair Kit † Included in Fluid Seal Repair Kit 24B675 Not sold separatelyOrifice Repair KitsGeneral Metal Applications SizeModel has Fluid Control Knob for fine adjustment of fluid flow High Wear ApplicationsWood Applications Needle tip and nozzle exit constructed from tungsten carbideManifold with bottom fluid ports 114101 103 107 105108Not shown Not sold separately Part No. 24C342 Not shown, optional size Not sold separately Part No. 288223 onlyPart No. 24C342 only 107 101 114 103 North America Manifold with side fluid portsInternational Manifold with side fluid ports Not shown, optional size Not sold separately Part No. 288217 only2 Torque to 8-10 in-lb 0.9-1.3 Nm Not shown, optional size Not sold separately Part No. 288160 onlyPart No. 288211 only 3 Torque to 110-130 in-lb 12.3-4.7 NmReplacement Gun 24A780 AccessoriesCleaning Brush Alternate Nozzle SizesSpray Tip Filters HVLP Pressure Verification KitInline Fluid Filter 24B707 TipsDimensions Manifold Models 288217 or 288218, All Gun ModelsManifold Model 288221, All Gun Models Manifold Model 288223 or 24C342, All Gun Models Manifold Model 288160 or 288211, All Gun ModelsTwo M5 x 0.8 x 0.25 in. 6.3 mm holes Mounting Hole LayoutsManifold Models 288217 or 288218, All Gun Models Two 0.13 diameter 0.31 in. 7.8 mm holes. Use 1/8 in. pinTwo 0.13 diameter 0.31 in. 7.8 mm holes. Use 1/8 in. pin Manifold Model 288221, All Gun ModelsTwo M5 x 0.8 x 0.25 in. 6.3 mm holes for alignmentMounting Hole Layouts Manifold Model 288223 or 24C342, All Gun Models6.3 mm holes Four M6 x 1.0 x 0.34 inTwo 0.13 diameter 0.31 in. 7.8 mm holes. Use 1/8 in. pin Manifold Model 288160 or 288211, All Gun ModelsTwo M5 x 0.8 x 0.25 in. 6.3 mm holes for alignmentMounting Hole Layouts Retrofit Adapter Plate2.3 in 57.7 mm ti8178aSound Data Technical DataTriggering Speed Cylinder AirGraco Standard Warranty Graco Information