Manuals / Graco / Power Tools / Paint Sprayer

Graco ti13585a, ti13586a important safety instructions Setup, Connect Air Line, Connect Fluid Hose

Models: ti13585a

1 44

Download 44 pages 28.69 Kb

Page 14

Setup

Setup

Setup

Connect Air Line

NOTE:

•You must install an air pressure regula- tor (F) on each gun air line to control air pressure to the gun. See FIG. 6.

•If your regulated air source does not have a filter, install an air filter (G) on each air line to ensure a dry, clean air supply to the gun. Dirt and moisture can ruin the appearance of your finished workpiece. See FIG. 6.

•Install a bleed type air shutoff valve (E) on each gun air supply line, down- stream of the gun air regulator, to shut off air to the gun.

1.For manifolds with a separate ATOM and FAN port, the gun cylinder, fan, and atomi- zation air must be supplied and regulated separately. For the manual fan valve mani- fold, only one supply line is required for both atomization and fan air.

NOTE: The gun atomizing and fan air inlets are 3/8 in. O.D. tubing. The cylinder air inlet accepts 1/4 in. (6.3 mm) O.D. tubing. Use 3/8 in. (9.5 mm) O.D. tubing for fan and atomiza- tion air to minimize excessive pressure drop in the hoses.

2.Connect each air hose (D) to a regulated air supply line (H).

H

G	F E D	ti01990
		ti01990

FIG. 6: Connect Air Line

Connect Fluid Hose

NOTE:

•Before connecting the fluid line, blow it out with air and flush it with solvent. Use solvent that is compatible with the fluid to be sprayed.

•Install a fluid regulator (L) on the fluid line to control fluid pressure to the gun.

•Install a fluid shutoff valve (M) to shut off the fluid supply to the gun.

•Filter the fluid line of coarse particles and sediment to avoid clogging the fluid nozzle and causing finishing defects. Inline fluid filter 24B707 is available. See Accessories, page 34.

1.Connect the fluid supply hose (J) to the gun fluid inlet (S), 1/4 npsm thread. See FIG. 8.

2.Connect the other end of the fluid hose (J) to a regulated fluid supply outlet (M).

3.In a circulating system, connect a grounded fluid return hose to the gun fluid outlet (T). See FIG. 8.

In a non-circulating system, remove the gun fluid outlet fitting (T) and plug the outlet port with the pipe plug supplied. See FIG. 8.

K

L

M

J

ti7016a

FIG. 7: Connect Fluid Hose.

14

313516G

Image 14

Graco ti13585a, ti13586a important safety instructions Setup, Connect Air Line, Connect Fluid Hose

Contents

Instructions-Parts Important Safety InstructionsAutomatic AirPro Spray Guns 313516GApplication ContentsModels Orifice SizeEQUIPMENT MISUSE HAZARD WarningsFIRE AND EXPLOSION HAZARD PERSONAL PROTECTIVE EQUIPMENT PRESSURIZED EQUIPMENT HAZARDTOXIC FLUID OR FUMES HAZARD TERMS Selection ChartsGeneral Metal Applications With Fluid Control Knob for fine adjustment of fluid flowGun Selection High Wear ApplicationsWood Applications HVLP GunsConventional Guns Proper Needle/Nozzle SelectionAir Caps Fan Air Air FlowAtomizing Air Maximum HVLP/Compliant inlet manifold pressure Atomizing AirFan Air Configure Gun and Manifold InstallationVentilate Spray Booth Circulating SystemGround System Install Air FittingsGround Air Compressors and Hydraulic Power Supplies Ground Spray GunStationary Support Mount GunReciprocating Arm Rod Mount Retrofit Adapter Plate FIG. 5 Retrofit Adapter Plate MountConnect Fluid Hose SetupConnect Air Line Side Mounted Manifold Ports Flush Spray GunPosition Air Cap Bottom Mounted Manifold PortsAtomization Adjust Spray PatternTable 1 Suggested Starting Settings Fan Air psiNOTE HVLP and Compliant Gun Limits Apply Fluid Pressure Relief ProcedureOperation IncorrectDaily Gun Care General System Maintenance Clean and Flush GunProblem TroubleshootingGeneral Troubleshooting SolutionSolution Spray Pattern TroubleshootingProblem ProblemService Disassembly14. Perform the following applicable step Reassembly ti13593b PartsParts Included in Air Seal Repair Kit † Included in Fluid Seal Repair Kit 24B675 Not sold separatelyOrifice Repair KitsGeneral Metal Applications SizeModel has Fluid Control Knob for fine adjustment of fluid flow High Wear ApplicationsWood Applications Needle tip and nozzle exit constructed from tungsten carbideNot shown Not sold separately Manifold with bottom fluid ports114101 103 107 105108 Part No. 24C342 only Part No. 24C342Not shown, optional size Not sold separately Part No. 288223 only 107 101 114 103 North America Manifold with side fluid portsInternational Manifold with side fluid ports Not shown, optional size Not sold separately Part No. 288217 only2 Torque to 8-10 in-lb 0.9-1.3 Nm Not shown, optional size Not sold separately Part No. 288160 onlyPart No. 288211 only 3 Torque to 110-130 in-lb 12.3-4.7 NmReplacement Gun 24A780 AccessoriesCleaning Brush Alternate Nozzle SizesSpray Tip Filters HVLP Pressure Verification KitInline Fluid Filter 24B707 TipsManifold Model 288221, All Gun Models DimensionsManifold Models 288217 or 288218, All Gun Models Manifold Model 288223 or 24C342, All Gun Models Manifold Model 288160 or 288211, All Gun ModelsTwo M5 x 0.8 x 0.25 in. 6.3 mm holes Mounting Hole LayoutsManifold Models 288217 or 288218, All Gun Models Two 0.13 diameter 0.31 in. 7.8 mm holes. Use 1/8 in. pinTwo 0.13 diameter 0.31 in. 7.8 mm holes. Use 1/8 in. pin Manifold Model 288221, All Gun ModelsTwo M5 x 0.8 x 0.25 in. 6.3 mm holes for alignmentMounting Hole Layouts Manifold Model 288223 or 24C342, All Gun Models6.3 mm holes Four M6 x 1.0 x 0.34 inTwo 0.13 diameter 0.31 in. 7.8 mm holes. Use 1/8 in. pin Manifold Model 288160 or 288211, All Gun ModelsTwo M5 x 0.8 x 0.25 in. 6.3 mm holes for alignmentMounting Hole Layouts Retrofit Adapter Plate2.3 in 57.7 mm ti8178aSound Data Technical DataTriggering Speed Cylinder AirGraco Standard Warranty Graco Information