Crathco Granita Preventive Maintenance (PM)

Checklist for Kit 90566 -

Serial # 11259 and above

(and units with lower serial #’s that have been converted to stainless steel shafts - units with black stainless shafts will need to be converted using PM Kit # 90110B)

Model # ___________________________

Serial # ____________________________

Date: ______________________________

PM by _____________________________

Of Company ________________________

Store Name/# _______________________

Address ___________________________

__________________________________

Store Mgr Name ____________________

Signature __________________________

A preventive maintenance visit should be performed every 6 months. In addition, air filter should be cleaned weekly, and every three months the condenser should be cleaned, and the rubber shaped bell shaft seals should be replaced. Failure to complete PM’s every 6 months is considered abuse of the machine, and therefore voids the warranty. Proof of PM must be documented with Grindmaster Corporation to maintain warranty coverage. To docu- ment your PM, complete this form with signatures, place used/worn parts that were replaced during the PM inside envelope, and mail to Grindmaster Corporation. Parts returned should include 2 evaporator seals, 2 rubber bell shaped shaft seals, valve o-rings and shafts (if applicable). First PM on serial numbers 11259 to 12202 should also include kit number 90225 (one per serial number).

The following procedures should be performed during a Preventative Maintenance visit, using PM kit # 90566 or 90110B.

Document model and serial number of equipment and record above.

Check product temperature and consistency for proper setting - adjust if necessary.

Insure product is being mixed properly and is within specification (check and document brix - most products should be around 13% - refer to product manufacturer’s recommendations for exact recommended brix). Record Brix reading here: Left Bowl _____ Right Bowl _____

Check for leaks at gaskets, o-rings, front shaft seal, etc. Empty product from bowls and disassemble unit completely. Clean and sanitize all disassembled parts.

Clean and sanitize top tray and freezing barrel.

Clean out condensation tube with sanitizer and long brush. Check condition of all panels, bowls, lids - replace if necessary.

Check mixing rods and augers for wear, check mixing rod bearing for wear - replace if necessary. Check for bowl knobs (two per bowl to lock down bowl in front) - replace if necessary.

Check operation of lights in lid and rear of unit (if equipped) - replace light bulbs if necessary. Clean re-usable air filter. Check condition of filter and replace if necessary.

Clean condenser.

Check condition of bowl gaskets and replace if necessary. Replace all o-rings on dispense valves and lubricate.

Check drive shaft. Replace if necessary, using PM kit #90110B in place of 90566 above.

Replace evaporator seal in front of evaporator. (use brass tool, included, to slide seal onto shaft, and use the white tool to tap seal into place. Be sure to lubricate seal with food grade grease first)

Replace bell shaped rubber shaft seal on front of freezing barrel (generously lubricate inside seal)

Lubricate parts where appropriate (dispense valve o-rings, inside of shaft seal, inner rim of bowl where it meets with the bowl seal)

Re-assemble unit and refill with product

Verify and document defrost timer setting and operation and time of day setting and adjust if necessary. Check thermostat setting on MG models. Thermostat setting should be between 1-1/2 and 2.

Verify compressor operation and freezer controller operation. Verify ventilation is adequate (8” on both sides and back) Check electrical connections and wiring.

Check fan operation (1 condenser fan and 2 gear motor fans) and clean fan or blades if necessary. Review proper periodic care and cleaning instructions (disassembly, cleaning, sanitizing, lubrication and

re-assembly) with store personnel. Review proper product mixing and handling instructions with store personnel Demonstrate and train store personnel to follow proper procedures (stress importance of store level

maintenance such as lubrication and filter cleaning).

Make sure store personnel have appropriate supplies (lubricant and sanitizer) to care for machine.

Page 14

G & MG Series Granita Machine

Page 13 Page 15
Page 14
Image 14
Grindmaster G & MG Series Crathco Granita Preventive Maintenance PM, Checklist for Kit Serial # 11259 and above
Page 13 Page 15

G & MG Series specifications

Grindmaster G & MG Series showcases a remarkable innovation in the world of coffee grinding technology, blending efficiency, durability, and performance to meet the needs of coffee enthusiasts and professionals alike. These grinders are designed to deliver a superior grinding experience, ensuring that every bean is ground to perfection.

One of the standout features of the Grindmaster G & MG Series is its grinding consistency. Utilizing advanced burr grinding technology, these machines maintain an even grind size, essential for achieving the ideal flavor extraction in every brew. The series includes both flat and conical burr options, allowing users to select the type that best matches their brewing method. This versatility is critical for accommodating a range of coffee styles, from espresso to French press.

Another key characteristic of the G & MG Series is its user-friendly interface. Featuring intuitive controls and clear display options, operators can easily adjust grind settings to achieve their desired consistency. The timers and dosing controls enable precise measurements, ensuring that every cup is brewed with the exact amount of coffee needed for optimal taste.

Durability is a hallmark of the Grindmaster brand, and this series is no exception. Built with robust materials, the G & MG Series is designed to withstand the demands of high-volume coffee environments, such as cafes and restaurants. The components are engineered for longevity, minimizing maintenance downtime and ensuring that the grinder remains a reliable tool in any setting.

Furthermore, the Grindmaster G & MG Series integrates innovative technologies to enhance user experience. The models are equipped with noise-reducing features, making them suitable for environments where quiet operation is essential. Additionally, some models in the series offer advanced thermal stability technology, which helps maintain consistent performance without overheating.

In terms of design, the G & MG Series showcases a sleek, modern aesthetic that fits seamlessly into any café or kitchen decor. The grinders are available in various colors and finishes, allowing business owners to choose a look that aligns with their brand identity.

In conclusion, the Grindmaster G & MG Series stands out as a top choice for coffee grinding, combining advanced technology, user-friendly features, and robust construction. Whether for home use or commercial applications, these grinders provide an exceptional grinding experience, ultimately elevating the quality of coffee served.
Top Page Image Contents