Safety Labels Breakdown and Parts List | Grizzly G0659 instruction

Safety Labels Breakdown and Parts List

243

250

244

249

245

248

	(Next to Power Cords)

		246


246				247

REF	PART #	DESCRIPTION

243	P0659243	MACHINE ID LABEL
244	P0659244	EYE INJURY HAZARD LABEL
245	P0659245	DISCONNECT FROM POWER LABEL
246	PLABEL-14	ELECTRICITY LABEL

REF	PART #	DESCRIPTION

247	P0659247	GRIZZLY LABEL PLATE
248	P0659248	DOOR INJURY LABEL
249	P0659249	BLADE WARNING LABEL
250	PLABEL-12	READ MANUAL 2" X 3 5/16"

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.

-54-	G0659 9" x 14" Vertical Metal-Cutting Bandsaw

Image 56

Grizzly G0659 owner manual Safety Labels Breakdown and Parts List

Contents

Model G0659 Ss ,EAD from Leadbased PAINTS Table of Contents Contact Info IntroductionForeword Functional Overview Identification Machine Data Sheet Main Specifications Cutting Capacity #4/..3!&%49 !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 3AFETYYNSTRUCTIONSSFORR-ACHINERY Safety Instructions for Metal Cutting Bandsaws 220V Single-Phase Circuit Requirements Setup Setup Safety InventoryUnpacking Main Components Figure Qty Clean Up Placement LocationSite Considerations Floor Load Moving & Placing Leveling MachineTools Needed Qty To level the machine Mounting to Shop Floor Removing Shipping BracketBolting to Concrete Floors To remove the shipping bracket Assembly To assemble the bandsaw Recommended Adjustments Factory adjustments that should be verifiedTest Run To test run the machine Operation Safety Basic Controls Operations Counterweight controls Upper Wheel Tracking Adjustment Adjusts blade tracking Angle Adjustments Clamp Vise installationClamp Vise Clamp Vise Removal To adjust the depth of cut To adjust the feed rateCutting Depth Feed Rate To properly position the guide post To adjust the feed pressureFeed Pressure Guide Post Adjusting Saw Frame Stop To adjust the saw frame stopLocking Blade To lock the blade in the forward position Blade Selection Blade TerminologyBlade Length Blade Width Tooth Set Tooth Type Blade Pitch TPI To select the correct blade pitch Blade Breakage Blade Care Break-InBlade Care Blade Break-In To correctly tension the blade Blade TensioningBlade Changes Adjusting Blade Guides Upper and Lower Guide Bearing Adjustment Lower Blade Guide Assembly Adjustment To position the lower blade guide assembly Blade Tracking Upper Blade Guide Assembly AdjustmentTo position the upper blade guide assembly To change the blade speed Changing SpeedsChanges in the blade tension may change the blade tracking Tanks, Cylinders, Containers, Valves, Etc Workpiece InspectionCutting Tips Straight Cuts Freehand Cuts To prepare the G0659 for freehand cuts Chip Inspection Chart AdditionalAppearance Actions Accessories Grizzly Bandsaw BladesG7315-Super Heavy-Duty Mobile Base G1928-Bandsaw Handbook Maintenance CleaningSchedule Redressing Rubber Tires Lubrication Chip Tray Motor & Electrical ServiceTroubleshooting Cutting Operations Miscellaneous Tensioning Replacing V-BeltTo align the V-belt pulleys To check/replace the V-belt To check if the wheels are parallel and copla- nar Wheel AlignmentMaterials Needed Qty Upper wheel adjustments To adjust the wheel coplanarity To adjust the blade scraper and brush Blade Scraper Wheel Brush G0659 Wiring Diagram 110 VAC Motor junction box wiring G0659 Electrical Components G0659 Hydraulic System Schematic See Figure Upper Saw Frame Breakdown Upper Saw Frame Parts List Description Lower Saw Frame Breakdown and Parts List Gearbox Breakdown and Parts List Drive Unit Breakdown and Parts List Table Base Parts Breakdown Table Base Parts List Cabinet Base Breakdown and Parts List Safety Labels Breakdown and Parts List 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!-7! Warranty and Returns #ALL 4ODAYD&ORO! &2%%