Machine Data Sheet | Grizzly G9983 guide

MACHINE DATA

SHEET

Customer Service #: (570) 546-9663 ¥ To Order Call: (800) 523-4777 ¥ Fax #: (800) 438-5901

MODEL G9983

15" OPEN-END WIDE-BELT SANDER

Design Type	Floor Model - Open End
Overall Dimensions:
Height	613Ú4"
Width	35"
Depth	321Ú2"
Shipping Weight	923 lbs.
Net Weight	815 lbs.
Foot Print	29 x 231Ú2"
Crate Size	351Ú2" L x 37" W x 70" H
Capacities:
Maximum Board Width (in one pass)	15"
Maximum Board Thickness	51Ú2"
Minimum Board Length	12"
Surface Speed of Sanding Belt	2050 FPM
Conveyor Feed Rate	13.1 & 16.4 FPM
Sanding Belt Size	16" x 48"
Sanding Motor:
Horsepower	5 HP
Voltage	220V
Amps	30
RPM	1725
Phase Ú Cycle	Single Ú 60 HZ
Power Transfer	2 V-Belt Drive
Conveyor Motor:
Horsepower	1Ú4 HP
Voltage	220V
Amps	1.8
RPM	1725
Phase Ú Cycle	Single Ú 60 HZ
Power Transfer	Gear Box to Chain
General Construction:
Cabinet	Steel
Belt Drums	Rubber Infeed Drum
................................................................................................................	Steel Outfeed
..............................................................................................	Rubber Pressure Rollers
Features:
............................................................................................	Independent Motor Control
............................................................................................	Pneumatic Belt Tensioning
................................................................................................	Pneumatic Belt Tracking
....................................................................................................................	Load Meter
........................................................................................................	Safety Shut-Off Bar
............................................................................................................	Thickness Scale
......................................................................	Disc Brake System for Emergency Stops
....................................................................................................................	5" Dust Port

Specifications, while deemed accurate, are not guaranteed.

G9983 15" Open-End Wide-Belt Sander

-37-

Image 39

Grizzly G9983 instruction manual Machine Data Sheet

Contents

OPEN-END WIDE-BELT Sander Page Table Of Contents Safety Instructions For Power Tools Safety 25ft 50ft 100ft Length AMP Rating Additional Safety Instructions For The Wide-Belt Sander Introduction Circuit Requirements 220V Single-Phase Wiring GroundingExtension Cords External Features Control Panel Machine Features These items are behind Left-hand access door Access Doors SET UP UnpackingPiece Inventory Measure Hardware Recognition Chart Site Considerations Clean Up Beginning Assembly To install the handwheel handleHandwheel Handle Platen To insert the platenTo set the platen even with the belt rollers To connect the air hose To install a sanding beltAir Hose Sanding Belt Sanding Belt Tension Pressure Rollers To Tighten Belt TensionTo Loosen Belt Tension Before you test run your machine Dust Collection Test Run Recommended adjustment checklist Recommended Adjustments Grit Type OperationsBefore Starting Choosing Sandpaper To change feed belt speeds Unplug the sander Conveyor Height Feed Belt Speed This is the load meter Load Meter Operation Three basic platen positions Platen Depth Cleaning Pads Emptying Filters MaintenanceCleaning Sanding Belts General Date Approximate Hours Of Use Maintenance Performed Oscillation Timing Service Adjustments Use the knob on this valve to control Oscillation speed Oscillation Speed Oscillation Return Limit SwitchesTo adjust the oscillation return To adjust the limit switches Pressure Roller Depth To adjust the pressure roller depth Unplug the sander Pressure Roller Tension To adjust the pressure roller tension Unplug the sander To check the feed belt tracking To adjust the feed belt tracking Unplug the sanderFeed Belt Tension Feed Belt Tracking Replacing V-Belts Belt Tension G9983 15 Open-End Wide-Belt Sander To replace the graphite sheet Platen Graphite Air System Replacing Brakes Date Approximate Hours Of Use Service Performed Closure Machine Data Sheet Air Inlet Motor 5 6 8 9 10 11 14 Model G9983 Wiring Diagram 220 Volt Single Phase Platen Tool G9983 Parts Breakdown 109108 124 111 110 112 Machine Base Roller Bracket LH G9983 Contact Roller Base 414 Machine Frame 621 622 620 601 619 623 Control BOX Symptom Possible Cause Corrective Action Troubleshooting Tion Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC Page Call Today For a Free Full Color Catalog