System Configuration
To set the delay times, follow these steps:
1.Put the AVR 120 in the Dolby Pro Logic II mode by pressing the Surround Mode Selector 7 on the front panel or by pressing the Surround Mode Selector jon the remote, until PRO LOGIC II appears in the Main Information Display F and the Pro Logic II Indicator D lights up.
2.Press the Delay Button 29 23 on the remote or front panel. The words S DELAY TIME will appear in the Main Information Display F.
3.Press the Set Button o21 .
4.Adjust the delay time by pressing the ▲/▼ Buttons mq on the remote or the Selector Buttons 5 on the front panel until the delay time figure calculated using the formula entered above appears in the display.
5.If only analog sources will be used, no adjustment is needed for the
6.Before setting the
7.Select the Dolby Digital mode by pressing either the Surround Mode Selector 7 on the front panel or the Surround Mode Selector j on the remote, until DOLBY DIG appears in the Main Information Display F.
8.Press the Delay Button 29 23 on the remote or front panel. The words S DELAY TIME will appear in the Main Information Display F.
9.Press the Set Button o21 , and then immediately press the ▲/▼ Buttons mq on the remote or the Selector Buttons 5 on the front panel until the desired delay time for the surround chan- nels is shown in the display.
10. Press the Set Button o21 within three seconds after the desired setting is shown.
11.Press the ▲/▼ Buttons mq on the remote once so that C DELAY TIME appears in the Main Information Display
F.
12.Press the the Set Button o21 .
13.Press the ▲/▼ Buttons mq on the remote or the Selector Buttons 5 on the front panel until the desired delay
time for the center channel appears in the display.
14.Press the Set Button o21 to enter the setting into the AVR 120’s memory.
Additional Input Adjustments
In addition to the major adjustments described in the preceding pages, you may also wish to set the type of audio source type (analog or digital) to be used with an input at this time. Once a specific audio source type is associated with any of the inputs, it will remain in the memory until it is changed, even when another input is selected. To attach one of the digital inputs to a specific source, follow these steps:
1.Press the Digital Button p24 .
2.Immediately press the ▲/▼ Buttons mq or Selector Buttons 5 to scroll through the list of available digital inputs or the analog input.
3.When the desired input type is shown in both the Main Information Display F and in the Analog S, Coaxial Digital Input T or Optical Digital Input U Indicators, press the Set Button o21 to enter the setting into the unit's memory.
You may also “memorize” a specific surround mode so that it will always be used when an input is selected. The AVR 120 always remem- bers the last surround mode used with any input, but during the setup process you may wish to preset the modes for each source. To do that, follow these steps:
1.Select an input by pressing one of the Input Selectors e! or the AM/FM Tuner Select g.
2.Press the Surround Mode Selector
j7, and immediately press the ▲/▼ Buttons mq or Surround Mode Selector ! to scroll through the list of available surround modes. Note that the name of each mode will scroll from right to left across the Main Information Display
F. To avoid having the system “time out” and exit the select process, be sure to press the ▲/▼ Buttons mq or Surround Mode Selector ! to select the next mode at any time the mode name is displayed.
3.When the desired mode name appears in the Main Information Display F and in the Surround Mode Indicators 29 ,
simply pause for a few seconds to allow the unit to “time out.” Your selection will be memorized and will be activated each time the input is selected until another mode is selected.
4.Repeat the process for each of the inputs.
5.When the desired Surround mode has been entered for all inputs, press the Set Button o.
Once the settings outlined on the previous pages have been made, the AVR 120 is ready for operation. While there are some additional settings to be made, these are best done after you have had an opportunity to listen to a vari- ety of sources and different kinds of program material. These settings are described on pages 21 through 26 of this manual. In addition, any of the settings made in the initial configuration of the unit may be changed at any time. As you add new or different sources or speakers, or if you wish to change a setting to better reflect your listening taste, simply follow the instruc- tions for changing the settings for that parame- ter, as shown in this section.
Having completed the setup and configuration process for your AVR 120, you are about
to experience the finest in music and home theater listening. Enjoy!
