Advanced Features
The AVR5000 is equipped with a number of advanced features that add extra flexibility to the unit’s operation. While it is not necessary to use these features to operate the unit, they pro- vide additional options that you may wish to use.
Display Brightness
The AVR5000’s front panel Main Information Display Ûis set at a default brightness level that is sufficient for viewing in a normally lit room. However, in some home theater installa- tions, you may wish to occasionally lower the brightness of the display, or turn it off completely.
To change the display brightness setting for a specific listening session, you will need to make an adjustment in the ADVANCED SELECT menu. To start the adjustment, press the OSD button Lto bring the MAS- TER MENU to the screen. Press the ⁄ Button Dtwice, until the
* A D V A N C E D | S E L E C T | * | |||||
|
| ||||||
V F D | : | F U L L | H A L F O F F | ||||
|
|
|
|
|
|
|
|
V O L U M E D E F A U L T : | O F F | O N | |||||
D E F A U L T V O L | S E T : |
| |||||
S E M I O S D : O F F | O N |
|
| ||||
S E M I O S D T I M E O U T : | 3 5 | ||||||
F U L L O S D T I M E O U T : 2 0 5
R E T U R N T O M E N U
Figure 9
To change the brightness setting, at the ADVANCED SELECT menu, make cer- tain that the
VFD line, and press the › Button until the desired brightness level is highlighted in the video display. When FULL is highlighted, the display is at its normal brightness. When HALF is highlighted, the display is at half the normal brightness level. When OFF is high- lighted, all of the indicators in the Main Information Display Ûwill go dark. Note, however, that the green LEDs for the Input Indicators and the Surround Mode Indicators ˜, as well as for the Power Indicator 3, will always remain lit to remind you that the unit is turned on.
If you wish to make other adjustments in the menu, press the ⁄/¤ Buttons Duntil the on- screen › cursor is next to the desired setting or the RETURN TO MENU line and press the Set button F. If you have no other adjust- ments to make, press the OSD Button Lto exit the menu system.
The display brightness may also be changed by pressing and holding the Set button Ôon the front for three seconds until the message in the Main Information Display Yreads VFD FULL. Within five seconds, press the front panel Selector buttons 5until the desired brightness display level is shown. At that point, press the Set button Ôagain to enter the setting.
Once the desired brightness level is selected, it will remain in effect until it is changed again or until the unit is turned off.
Turn On Volume Level
As is the case with most audio/video receivers, when the AVR5000 is turned on, it will always return to the volume setting in effect when the unit was turned off. However, you may prefer to always have the AVR5000 turn on at a specific setting, regardless of what was last in use when the unit was turned off. To change the default condition so that the same volume level is always used at
At the ADVANCED SELECT menu make certain that the
ton so that the word ON is highlighted in the video display. Next, press the ¤ button D once so that the
Eor hold them pressed until the desired volume level is shown on the DEFAULT VOL SET line. Note that this setting may NOT be made with the regular volume controls.
NOTE: Since the setting for the
Óî. When the desired volume level to be used at
Unlike some of the other adjustments in this menu, the
If you wish to make other adjustments in the menu, press the ⁄/¤ Buttons Duntil the on- screen › cursor is next to the desired setting or the RETURN TO MENU line and press the Set button F. If you have no other adjust- ments to make, press the OSD Button Lto exit the menu system.
