Remote Control
Learning Codes from a Remote
The HS 350 remote is able to “learn” codes from other remote controls that might be part of your system setup, like the one from your TV. To learn or transfer codes from an IR remote to the HS’s remote, follow these steps:
1.Place the front of the original remote with the code being sent so that it is facing the IR
Transmitter Window on the HS remote
2.Select the button on the remote that you wish to use as the device selector for the codes about to be entered. This must be any of the Input Selectors 0.
3.Press the Input Selector 0 button chosen
and the Learn Button | at the same time. | |
Hold these buttons until the Program | ||
Indicator | flashes amber and the light | |
under the device selector button turns red. Release the buttons. It is important that you begin the next step within 20 seconds.
4.Press the button on the HS remote that you wish to program. Note that the Program
Indicator will stop flashing.
Important Note: Codes cannot be taught to all buttons on the remote. In these cases the
Program Indicator keeps flashing after the button was released.
5. As long as the Program Indicator is on steadily (for five seconds), press and hold the button on the original remote that you wish to “teach” into the HS remote. If you pressed the button too late or no command was received within five seconds, the Program Indicator
will flash red three times and then amber, then simply repeat step four. When the
Program Indicator | turns green, release |
the button on the original remote. Note that the Program Indicator will then begin to flash amber again.
NOTE: If the Program Indicator turns red
steadily during Step 5, the programming was not successful. Repeat the steps to see if the code will “take.”If the indicator keeps flashing red in step 5, this code cannot be taught.
6.Repeat steps 4 though 5 for each button on the source remote that you wish to transfer to the HS remote.
7.Once all codes have been transferred from the original source remote to the HS remote, press
the Learn button . This will turn off all LEDs and turn off the learning mode.
8.Repeat Steps 1 through 7 for any additional remotes you wish to “teach” into the HS Remote.
Erasing Learned Codes
The HS’s remote allows you to remove or erase the code learned into a single button for a single device, to remove or erase all the codes that have been learned for a single device, or to erase all commands that have been learned to all devices.
To erase a single learned code from within a single device’s settings, follow these steps:
1.Press and hold both the Input Selector 0 within which the individual button to be erased has been programmed and the
Learn button | . |
2.When the red LED under the Input Selector turns red and the Program Indicator flashes amber, release the buttons.
3.Press and release the Input Selector 0 again for the device within which the individual button to be erased has been programmed.
4. Press the 7 button | three times. |
5.Press and release the individual button for which the code is to be erased. The Program
Indicator will blink green two times and then return to amber.
6.To erase other buttons within the same device, press them as noted in Step 5.
7.When all buttons to be erased have been
pressed, press the Learn button | to |
complete the process. |
|
To erase all codes within a single device, follow these steps:
1.Press and hold both the Input Selector 0 for which you wish to erase the codes and the
Learn button | . |
2.When the red LED under the Input Selector turns red and the Program Indicator flashes amber, release the buttons.
Macro Programming
Macros enable you to easily repeat frequently used combinations of commands with the press of a single button on the HS’s remote control. Once programmed, a macro will send out up to 19 different remote codes in a
1.To start programming a macro, press the Mute button A and the Macro button K to be programmed at the same time. Note that the latest selected Input Selector will light red,
and the Program Indicator | will flash |
amber. |
|
2.Enter the steps for the macro sequence by pressing the button for the actual command step. Although the macro may contain up to 19 steps, each button press, including those used to change devices, counts as a step.
The Program Indicator will flash green twice to confirm each button press as you enter commands.
NOTE: While entering commands for Power On of any device during a macro sequence, press the Mute button A. DO NOT press the Power ON button 0.
•Remember to press the appropriate Input Selector button 0 before functions are changed to another device.
3. When all the steps have been entered, press the Preset Up / PIC+ button L to enter the commands. The red light under the Input Selector 0 will blink and then turn off and
the Program Indicator will flash green twice to confirm the macro to be programmed.
ENGLISH
REMOTE CONTROL 29
