DVP-HSM-B & DVP-TVHW Components for Indoor Fireplaces | Hearth and Home Technologies

B. Vent Components Diagrams (continued)

7-3/8 in.

1-1/2 in.

3-7/8 in.

14 in.

12 in.

17-3/4 in.

10-1/2 in.

DVP-TV

Vertical Termination Cap

Not for use on these models.

DVP-TB1

Basement Vent Cap

31 in.

13-1/4 in.

24-5/8 in.

24-5/8 in.

27-1/2 in.

13-1/4 in.

RF6M	RF12M	DVP-TRAPFL
Roof Flashing Multi-pak	Roof Flashing Multi-pak	Flashing
		Flashing
13-3/4 in.	5 in.
	7-1/4 in.

13-3/4 in.

BEK

Trap Cap Brick Extension

13-7/8 in.					9-1/2 in.

14 in.

DRC-RADIUS

Cap Shield

DVP-HSM-B

Extended Heat Shield

Figure 16.4 DVP vent components

12-1/2 in.

5-1/4 in.

	DVP-TVHW
	Vertical Termination Cap (High wind)
	11-5/8 in.
7-1/8 in.	12-1/8 in.
7-1/8 in.
	5-3/4 in.
	COOL-ADD
	Cap Shield
	(For use on
	Intellifire
PVK-80	appliances only)
Power Vent

56	Heat & Glo • 6000GCF-IPI, 6000GCF-IPILP • 2110-900 Rev. H • 11/08

Image 56

Hearth and Home Technologies 6000GCF-IPIL owner manual Dvp-Hsm-B, Not for use on these models

Contents

What to do if you smell gas HOT Surfaces Xxxxxxxx CongratulationsHomeowner Reference Information Table of Contents User Guide Appliance Setup TroubleshootingFinishing Reference Materials CONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Listing and Code Approvals Installation of Carbon Monoxide Detectors Requirements for the Commonwealth of Massachusetts Your Fireplace Gas Fireplace SafetyOperating Instructions User Guide Fixed Glass Assembly Remote Controls, Wall Controls and Wall SwitchesFan Kit optional Clear Space Lighting Instructions IPI Final inspection byWhat to do if YOU Smell GAS GAS Valve After Fireplace is Lit Frequently Asked QuestionsIssue Solutions Maintenance and Service Maintenance Tasks-HomeownerGlass Cleaning Remote Control Maintenance Tasks-Qualiﬁed Service Technician Gasket Seal and Glass Assembly InspectionVenting Logs Either cobrahead or SIT Getting Started Typical Appliance System Inspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Framing and Clearances Selecting Appliance Location Clearances Minimum Framing DimensionsConstructing the Appliance Chase Combustible Mantel Legs or Wall Projections Mantel and Wall ProjectionsCombustible Mantels Termination Locations Vent Termination Minimum Clearances = Area Where Terminal is not Permitted = Vent Terminal = AIR Supply Inlet Vent Information and Diagrams Approved PipeVent Table Key Use of Elbows Vent Diagrams Top Vent Horizontal Termination SLP series vent pipe, if desired Top Vent Horizontal Termination Three Elbows Chart Break Here Top Vent Vertical Termination Two Elbows H1 Maximum V1 + Minimum Heat Shield Above First 900 Elbow Vent Clearances and FramingPipe Clearances to Combustibles Non-Combustible Wall Penetration Wall Penetration FramingCombustible Wall Penetration Install the Ceiling Firestop Pipe DVP Vaulted Ceiling Installation Install Attic Insulation ShieldFlat Ceiling Installation Attaching Sheetrock Ledges Temporary Access PanelAppliance Preparation Installing the Fiberglass Gasket Securing and Leveling the Appliance Installing Vent Pipe Attach Vent to the Firebox AssemblyAssemble Vent Sections Assemble Pipe Sections Assemble Slip Sections Secure the Vent Sections 10 Rotate Seams for Disassembly Disassemble Vent Sections Install Metal Roof Flashing Assemble and Install Storm Collar Install RF4-8 Apply Sealant TOP & Partial Sides Install Vertical Termination Cap Heat Shield Requirements for Horizontal Termination Install Horizontal Termination Cap Ansi Z223.1 and CAN/CGA-B149 installation codes Gas Information Fuel ConversionGas Pressure Gas Connection Wiring Requirements Intelliﬁre Ignition System WiringOptional Accessories Requirements Electrical Information Electrical Service and Repair Intelliﬁre Pilot Ignition IPI Wiring Diagram Junction Box Installation Wall Switch Installation for Fan Optional Finishing Facing Material Appliance Setup Ember Material Install the RefractoryEmber Placement Install the Log Assembly Log #1 SRV2103-107 12 Front View Install the Mesh Install Trim and/or SurroundAir Shutter Setting Air Shutter Settings Intelliﬁre Ignition System TroubleshootingSymptom Possible Cause Corrective Action Ues to spark, and main Appliance Dimension Diagram Reference Materials Vent Components Diagrams DVP vent components DVP-TRAP DVP vent components DVP-HSM-B Not for use on these models DVP-HRC-SS DVP-HRC-ZC-SS Horizontal Termination CAP Log Set Assembly Service Parts At Depot Service Parts ListStocked 6000GCF-IPI Contact Information