7 | Accessories |
|
|
|
|
| |
A. Gas Log/Lighter Provisions |
|
| |
WARNING |
| ||
A certified gas log lighter or decorative gas log set can be |
| ||
installed in this fireplace. |
|
| |
Asphyxiation Risk |
| ||
• Maximum input is 100,000 BTU/hr. |
| ||
• Damper must be locked open when gas logs |
| ||
• Decorative gas appliance must be certified to ANSI Z21.60 | installed. |
| |
“Standard for Decorative Gas Appliances for Installation | Gas fire generates fumes. |
| |
in Vented Fireplaces”. |
| ||
|
| ||
•Must be installed in accordance with the National Fuel
Gas Code, ANSI Z223.1.
•A log set must incorporate a gas shutoff.
•Log set requires the damper to be locked fully open.
Knockouts are provided on both sides of the fireplace and in refractories for 1/2 in. (13 mm) iron pipe.
•We recommend you seal refractory around pipe with fireplace mortar or high temperature, noncombustible sealant.
•Repack insulation from the knockout around the pipe.
•Maintain
•See Figure 7.1.
WARNING
Fire Risk
•For use with solid wood fuel or decorative gas appliance only.
•DO NOT install unvented gas logs.
WARNING
Fire Risk
Explosion Risk
Inspect appliance and components for damage. Damaged parts may impair safe operation.
Firebox
Refractory 
Seal with 
fireplace mortar 
or high temp 
noncombustible 
sealant 
Outer Shell
of Fireplace
Maintain air clearance 
to combustibles.
Combustible
Materials
•Do NOT install damaged components.
•Do NOT install incomplete components.
•Do NOT install substitute components
Report damaged parts to dealer.
B. Junction Box Installation
Your appliance is supplied with a Junction Box Kit. We rec- ommend the junction box be installed and wired at this time to avoid reconstruction.
Gas Line 
Repack
Insulation
Knockout
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| (38 mm) |
|
|
|
|
|
|
|
|
|
|
| |
|
|
| Gas Line |
|
|
|
|
| air space | ||
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
| Combustible materials | |||||
|
|
|
|
|
| ||||||
|
|
|
|
|
| ||||||
|
|
|
|
|
| may be located at zero | |||||
|
|
|
|
|
| ||||||
|
|
|
|
|
| clearance to gas line | |||||
|
|
|
|
|
| ||||||
|
|
|
|
|
| beyond 4 in. (102 mm) | |||||
|
|
| 4 in. |
|
| from fireplace side. | |||||
|
|
|
|
| |||||||
| (102 mm) |
|
|
|
|
|
| ||||
• The Junction Box Kit is to be installed on the right side of |
the appliance; remove and discard the metal knockout. |
• Attach the junction box bracket to the junction box as |
shown in Figures 7.2 - 7.4. |
• Bring the electrical wires to the inside of the junction box |
and secure in place with the Romex connector. |
• Install the duplex receptacle in the junction box and attach |
the cover plate. |
• Prior to attaching the junction box to the appliance, the |
heat shield supplied with your appliance must be installed. |
Insert the top flange of the heat shield through the electrical |
Figure 7.1 Gas Line Installation
knockout hole from the inside (Figure 7.5). |
•Attach the junction box bracket to the side of the appliance by slipping the bottom flange into the knockout hole. See Figure 7.5. Secure with the three screws provided in the fastener package.
24 | Heat & Glo • |
