14-1/2 | Hearth and Home Technologies EM-415H manual

		Inside
		Diameter
		8 in. (203 mm)
		Outside
	Effective	Diameter
	Effective	10-1/2 in.
	Height	10-1/2 in.
	Height	(267 mm)
	4-3/4 in.	(267 mm)
	4-3/4 in.
	(121 mm)

SL315/SL330 Offset/Return

14-1/2 in.

(368 mm)

24 in.

(610 mm)

AS8 Straight Attic Insulation Shield

10-1/2 in.

(267 mm)

2 in. (51 mm)

JB877 Chimney Joint Band

10-1/2 in. (267 mm)

CB876 Chimney Joint Band

A

B		14-1/2 in.
		(368 mm)
	Ceiling Firestop

Catalog #	A		B
FS338	0-deg.	14-1/2 in.		368 mm
FS339	15-deg.	18-3/8 in.		467 mm

FS340	30-deg.	23 in.		584 mm

12 in. (305 mm)

24-5/8 in.

(625 mm)

27-3/8 in.

(695 mm)

RF370 Roof Flashing

12 in. (305 mm)

24-5/8 in. (625 mm)

31 in. (787 mm)

RF371 Roof Flashing

40	Heat & Glo • EM-415/EM-415H • 31317 Rev Q • 10/06

Image 40

Hearth and Home Technologies EM-415H owner manual 14-1/2

Contents

Models EM-415 EM-415H Woodburning Fireplace Fire Risk Grate Listing Label Information/LocationNumber Table of Contents Appliance Certiﬁcation Listing and Code ApprovalsNot intended for use as a primary heat source Design and Installation Considerations Getting StartedNegative Pressure Asphyxiation Risk Marginal Location Typical Fireplace System Typical Fireplace System Inspect Fireplace and Components Tools and Supplies NeededFire Risk Explosion Risk Framing and Clearances Selecting Fireplace Location Clearances Clearances to Combustible Materials Sidewalls/Surrounds Frame the Fireplace ¨E. Construct the Chase Chimney Requirements Installation of Fireplace Install the Outside Air KitFire Risk Sharp Edges Asphyxiation Risk Risk of Smoke Spillage Ft min. from top of uppermost chimney section to air inlet Secure the Fireplace Position the FireplacePlace the Protective Metal Hearth Strips Level the Fireplace Chimney Assembly Height of Chimney Components Using Offsets/Returns Degree SL306 SL312 SL318 SL324 SL336 SL348 Install the Ceiling Firestops Assemble the Chimney Sections Double-check the Chimney Assembly Install the Attic Insulation ShieldSecure the Chimney Complete the Enclosure Chimney Termination Install the Chimney Air Kit required in Canada Install the Termination CapChase Top Installing an ST375 Square Termination Cap Accessories Junction Box InstallationGas Log/Lighter Provisions Gas Code, Ansi Z223.1 Installation of Fan Shock Risk Finishing Hearth Extension Finishing Material MantelGlass Doors Combustible Material Operating Instructions General Information Outside Air Clear Space Near the FireplaceFlue Damper Firescreen Grate Wood FuelFirewood Moisture Starting a Fire Troubleshooting Understanding Vent Problems Diagnostics and Problem Solving Diagnostic QuestionsSolutions Can’t get a good ﬁre going. What am I doing wrong? ﬁreplace burns the wood too fast. What can I do? Maintenance and Servicing the Fireplace Chimney Inspection/CleaningDisposal of Ashes Firebox Refractory Maintenance Task List When cleaning glass doorClean Chimney Fire Fireplace Dimensions Reference Materials ¨ B. Fireplace Components Catalog # Description Chimney Components Catalog # 14-1/2 1829 mm 10-7/8 276 mm 406 mm 508 mm Minimum Base Dimensions 28 X 28 with 32 X 32 with 23 X Minimum Base Dimensions 26.5 X 28 with 34 X 34 withTR442 TR442 / 444 TV 20 x Service Parts EM-415 Series Description of Part EM-415 EM-415H Qty Herringbone Brick Refractory option available week 03/04 This page intentionally left blank Warranty For Heat & GLO Fireplaces Limited Warranty Contact Information