Manuals / Hearth and Home Technologies / Household Appliance / Indoor Fireplace

Hearth and Home Technologies SL-950TV-IPI-E SL-550TV-IPI-E, Log Set Assembly, B. Service Parts

Models: SL-950TV-IPI-E SL-550TV-IPI-E SL-750TV-IPI-E

1 48

Page 41

B. Service Parts	SL-550TV-IPI-E

Service Parts Diagram	Beginning Manufacturing Date: June 2007
	Ending Manufacturing Date:_________

9 8

Log Set Assembly

4 1 5

Part number list on following page.

Heat & Glo • SL-550 / 750 / 950TV-IPI-E • 2119-900 Rev. H • 11/08

Page 41

Image 41

Hearth and Home Technologies SL-950TV-IPI-E SL-550TV-IPI-E, Log Set Assembly, B. Service Parts, Service Parts Diagram

Contents

Owner’s Manual Models SL-550TV-IPI-E SL-750TV-IPI-E SL-950TV-IPI-EWhat to do if you smell gas Homeowner Reference Information A. CongratulationsRead this manual before installing or operating this appliance Please retain this owner’s manual for future referenceSafety Alert Key Table of ContentsInstaller Guide 3 Maintenance and Service15 Troubleshooting 14 Appliance SetupA. Remove Glass Assembly B. Remove the Shipping Materials C. Clean the Appliance D. AccessoriesCONDITIONS, EXCLUSIONS & LIMITATION OF LIABILITY B. Limited Lifetime WarrantyHearth & Home Technologies LIMITED WARRANTY B. Limited Lifetime Warranty continued A. Appliance Certiﬁcation 1 Listing and Code ApprovalsB. Tempered Glass Speciﬁcations C. BTU SpeciﬁcationsE. Non-Combustible Materials Speciﬁcation D. High Altitude InstallationsF. Combustible Materials Speciﬁcation G. Electrical CodesB. Your Fireplace A. Gas Fireplace Safety2 Operating Instructions User Guide G. Remote Controls, Wall Controls and Wall Switches F. Fixed Glass AssemblyC. Fan Kit optional E. Decorative Doors and FrontsFinal inspection by I. Lighting Instructions IPIFOR YOUR SAFETY READ BEFORE LIGHTING 1. Turn off all electric power to the applianceJ. After Fireplace is Lit K. Frequently Asked QuestionsISSUE SOLUTIONSA. Maintenance Tasks-Homeowner 3 Maintenance and ServiceGlass Cleaning Remote ControlGasket Seal and Glass Assembly Inspection B. Maintenance Tasks-Qualiﬁed Service TechnicianVenting LogsFigure 3.2 IPI Pilot Flame Patterns Either cobrahead or SITA. Typical Appliance System Getting StartedInstaller Guide FRAMING HEADED OFF IN CEILING JOISTS SECTION 8.B OPTIONAL WALL SWITCHD. Inspect Appliance and Components B. Design and Installation ConsiderationsC. Tools and Supplies Needed E. Negative Pressure A. Selecting Appliance Location 5 Framing and ClearancesF A ModelMINIMUM FRAMING DIMENSIONS B. Constructing the Appliance ChaseC. Clearances Combustible Mantels D. Mantel and Wall ProjectionsNote All measurements are in inches Figure 5.4 Non-Combustible ZoneA. Vent Termination Minimum Clearances 6 Termination LocationsFire Risk Maintain vent clearance to combustibles as speciﬁed DO NOT pack air space with insulation or other materialsA. Vent Guidelines 7 Vent Information and DiagramsB. Vent System Conﬁguration Vent this appliance directly outsideA. Pipe Clearances to Combustibles 8 Vent Clearances and FramingB. Wall and Ceiling Penetration Framing C. Vertical Penetration Framing9 Appliance Preparation A. Installing Outside Air Kit Damper Assem- blyB. Gas and Electrical Connections C. Securing and Leveling the ApplianceA. Assembly of Vent Sections 10 Installing Vent PipeD. Install Attic Insulation Shield C. Securing Vent SectionsA. Fuel Conversion 11 Gas InformationB. Gas Pressure C. Gas ConnectionC. Optional Accessories Requirements A. Wiring RequirementsD. Electrical Service and Repair B. Intelliﬁre Ignition System WiringBROWN F. Wall Switch Installation for Fan Optional E. Junction Box InstallationNOTICE DO NOT wire 110 VAC to wall switchA. Mantel and Wall Projections 13 FinishingDimensions of Combustibles Dimensions of Non-CombustiblesB. Facing Material A. Remove Glass Assembly 14 Appliance SetupC. Clean the Appliance D. AccessoriesPlacing the Lava Rock E. Lava Rock, Mineral Wool/Ember PlacementModel SL-550TR-E, 750TR-E, 950TR-E SL-550TV-E, SL-750TV-E, SL-950TV-E F. Install the Log AssemblyLog Set Assembly LOGS-550-E, 750-E, 950-E Log #3 Locate the pin hole on the underside of log #3. Mate the pin hole with the shoulder screw located on the burner top. Push the left end of log # 3 toward the back of the ﬁrebox until it touches the lava rock retainer H. Install the Mesh G. Fixed Glass AssemblyI. Install Trim and/or Surround J. Install HoodA. Intelliﬁre Ignition System 15 TroubleshootingSymptom A. Incorrect wiringSymptom Intelliﬁre Ignition System - continuedVerify all connections to wiring diagram in manual. Verify With ﬁxed glass assembly in place, verify that ﬂame is en16 Reference Materials A. Appliance Dimension DiagramFigure 16.1 Appliance Dimensions GAS LINE ACCESSB. Service Parts Log Set AssemblySL-550TV-IPI-E Service Parts DiagramSL-550TV-IPI-E Service Parts Listat Depot StockedSL-750TV-IPI-E Service PartsLog Set Assembly Service Parts DiagramSL-750TV-IPI-E Service Parts Listat Depot StockedLog Set Assembly SL-950TV-IPI-EService Parts Service Parts DiagramStocked SL-950TV-IPI-EService Parts List at DepotService Parts IPI Valve AssemblySL-550 / 750 / 950TV-IPI-E Stockedand maintenance C. Contact Informationinstallation and operation DO NOT DISCARD THIS MANUAL

B. Service Parts

SL-550TV-IPI-E

Service Parts Diagram

Beginning Manufacturing Date: June 2007

Ending Manufacturing Date:_________

Log Set Assembly