Manuals / Hearth and Home Technologies / Household Appliance / Indoor Fireplace

Hearth and Home Technologies SL-550TV-IPI-E Getting Started, A. Typical Appliance System

Models: SL-950TV-IPI-E SL-550TV-IPI-E SL-750TV-IPI-E

1 48

Page 16

4	Getting Started	Installer Guide

A. Typical Appliance System

NOTICE: Illustrations and photos reﬂect typical installations and are for design purposes only. Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual

NON-COMBUSTIBLE ROOF FLASHING MAINTAINS MINIMUM CLEARANCE AROUND PIPE

VENT PIPE (SECTIONS 7 and 8)

CEILING FIRESTOP ON FLOOR OF ATTIC (SECTION 8.B)

FRAMING/HEADER (SECTION 5)

VERTICAL TERMINATION CAP (SECTION 4.D)

STORM COLLAR (SECTION 4.D)

VENT PIPE PENETRATES ROOF

PREFERABLY WITHOUT AFFECTING

ROOF RAFTERS (SECTION 8.B)

ATTIC INSULATION SHIELD (NOT SHOWN) MUST BE USED HERE TO KEEP INSULATION AWAY

FROM VENT PIPE IF ATTIC IS INSULATED (SECTION 10.D)

FRAMING HEADED OFF IN CEILING JOISTS (SECTION 8.B)

OPTIONAL

WALL SWITCH

MANTEL AND MANTEL LEG (SECTION 5.D)

SURROUND

HEARTH EXTENSION

GAS LINE

SECTION

Figure 4.1 Typical System

16	Heat & Glo • SL-550 / 750 / 950TV-IPI-E • 2119-900 Rev. H • 11/08

Page 16

Image 16

Hearth and Home Technologies SL-550TV-IPI-E Getting Started, A. Typical Appliance System, Installer Guide, Roof Rafters .B

Contents

What to do if you smell gas Models SL-550TV-IPI-E SL-750TV-IPI-E SL-950TV-IPI-EOwner’s Manual A. Congratulations Homeowner Reference InformationRead this manual before installing or operating this appliance Please retain this owner’s manual for future referenceTable of Contents Safety Alert KeyInstaller Guide 3 Maintenance and Service14 Appliance Setup 15 TroubleshootingA. Remove Glass Assembly B. Remove the Shipping Materials C. Clean the Appliance D. AccessoriesHearth & Home Technologies LIMITED WARRANTY B. Limited Lifetime WarrantyCONDITIONS, EXCLUSIONS & LIMITATION OF LIABILITY B. Limited Lifetime Warranty continued 1 Listing and Code Approvals A. Appliance CertiﬁcationB. Tempered Glass Speciﬁcations C. BTU SpeciﬁcationsD. High Altitude Installations E. Non-Combustible Materials SpeciﬁcationF. Combustible Materials Speciﬁcation G. Electrical Codes2 Operating Instructions User Guide A. Gas Fireplace SafetyB. Your Fireplace F. Fixed Glass Assembly G. Remote Controls, Wall Controls and Wall SwitchesC. Fan Kit optional E. Decorative Doors and FrontsI. Lighting Instructions IPI Final inspection byFOR YOUR SAFETY READ BEFORE LIGHTING 1. Turn off all electric power to the applianceK. Frequently Asked Questions J. After Fireplace is LitISSUE SOLUTIONS3 Maintenance and Service A. Maintenance Tasks-HomeownerGlass Cleaning Remote ControlB. Maintenance Tasks-Qualiﬁed Service Technician Gasket Seal and Glass Assembly InspectionVenting LogsEither cobrahead or SIT Figure 3.2 IPI Pilot Flame PatternsGetting Started A. Typical Appliance SystemInstaller Guide FRAMING HEADED OFF IN CEILING JOISTS SECTION 8.B OPTIONAL WALL SWITCHC. Tools and Supplies Needed B. Design and Installation ConsiderationsD. Inspect Appliance and Components E. Negative Pressure 5 Framing and Clearances A. Selecting Appliance LocationF A ModelC. Clearances B. Constructing the Appliance ChaseMINIMUM FRAMING DIMENSIONS D. Mantel and Wall Projections Combustible MantelsNote All measurements are in inches Figure 5.4 Non-Combustible Zone6 Termination Locations A. Vent Termination Minimum ClearancesFire Risk Maintain vent clearance to combustibles as speciﬁed DO NOT pack air space with insulation or other materials7 Vent Information and Diagrams A. Vent GuidelinesB. Vent System Conﬁguration Vent this appliance directly outside8 Vent Clearances and Framing A. Pipe Clearances to CombustiblesB. Wall and Ceiling Penetration Framing C. Vertical Penetration FramingA. Installing Outside Air Kit Damper Assem- bly 9 Appliance PreparationB. Gas and Electrical Connections C. Securing and Leveling the Appliance10 Installing Vent Pipe A. Assembly of Vent SectionsD. Install Attic Insulation Shield C. Securing Vent Sections11 Gas Information A. Fuel ConversionB. Gas Pressure C. Gas ConnectionA. Wiring Requirements C. Optional Accessories RequirementsD. Electrical Service and Repair B. Intelliﬁre Ignition System WiringBROWN E. Junction Box Installation F. Wall Switch Installation for Fan OptionalNOTICE DO NOT wire 110 VAC to wall switch13 Finishing A. Mantel and Wall ProjectionsDimensions of Combustibles Dimensions of Non-CombustiblesB. Facing Material 14 Appliance Setup A. Remove Glass AssemblyC. Clean the Appliance D. AccessoriesE. Lava Rock, Mineral Wool/Ember Placement Placing the Lava RockLog Set Assembly LOGS-550-E, 750-E, 950-E F. Install the Log AssemblyModel SL-550TR-E, 750TR-E, 950TR-E SL-550TV-E, SL-750TV-E, SL-950TV-E Log #3 Locate the pin hole on the underside of log #3. Mate the pin hole with the shoulder screw located on the burner top. Push the left end of log # 3 toward the back of the ﬁrebox until it touches the lava rock retainer G. Fixed Glass Assembly H. Install the MeshI. Install Trim and/or Surround J. Install Hood15 Troubleshooting A. Intelliﬁre Ignition SystemSymptom A. Incorrect wiringIntelliﬁre Ignition System - continued SymptomVerify all connections to wiring diagram in manual. Verify With ﬁxed glass assembly in place, verify that ﬂame is enA. Appliance Dimension Diagram 16 Reference MaterialsFigure 16.1 Appliance Dimensions GAS LINE ACCESSLog Set Assembly B. Service PartsSL-550TV-IPI-E Service Parts DiagramService Parts List SL-550TV-IPI-Eat Depot StockedService Parts SL-750TV-IPI-ELog Set Assembly Service Parts DiagramService Parts List SL-750TV-IPI-Eat Depot StockedSL-950TV-IPI-E Log Set AssemblyService Parts Service Parts DiagramSL-950TV-IPI-E StockedService Parts List at DepotIPI Valve Assembly Service PartsSL-550 / 750 / 950TV-IPI-E StockedC. Contact Information and maintenanceinstallation and operation DO NOT DISCARD THIS MANUAL