Appliance Setup | Hearth and Home Technologies ST-550TM-IPI instruction

14 Appliance Setup

A. Remove Fixed Glass Assembly	2. Place the rock media on the porcelain base pan as
See Section 14.F.	shown in Figure 14.2.
See Section 14.F.

B. Remove the Shipping Materials

Remove shipping materials from inside or underneath the ﬁrebox.

C. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated inside the ﬁrebox or underneath in the control cavity.

D. Accessories

Install approved accessories per instructions included with accessories. Install approved accessories per in- structions included with accessories. Contact your dealer for a list of approved accessories.

WARNING! Risk of Fire and Electric Shock! Use ONLY Hearth & Home Technologies-approved optional acces- sories with this appliance. Using non-listed accessories could result in a safety hazard and will void the warranty.

E. Rock Media Placement

WARNING! Risk of Explosion! Follow rock media place- ment instructions in manual. DO NOT place rock media directly over burner ports. Improperly placed rock media will interfere with proper burner operation.

Placing the Rock Media

Rock media is an approved accessory for this appliance. To place the rock media, follow these instructions.

1.Place the rock placement jig over the burner slot as shown in Figure 14.1. The rock placement jig is located in the base of the unit.

Figure 14.2 Rock Media on Base Pan

3.Remove the rock placement jig as shown in Figure 14.3. Place the rock placement jig in the base of the unit when ﬁnished.

Figure 14.3 Rock Media Jig Removal

4.Make sure that there is no rock media in the burner slot. See Figure 14.2.

Figure 14.1 Rock Placement Jig

Figure 14.4 Burner Slot Free of Rock Media

Heat & Glo • ST-550TM-IPI • 2142-900 Rev. B • 11/08

51

Image 51

Hearth and Home Technologies ST-550TM-IPI owner manual Appliance Setup

Contents

What to do if you smell gas Models Homeowner Reference Information Congratulations User Guide Table of Contents Reference Materials Appliance SetupTroubleshooting Finishing CONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide Detectors Gas Fireplace Safety Operating Instructions User GuideYour Fireplace Decorative Doors and Fronts Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Clear Space Final inspection by Lighting Instructions IPI After Fireplace is Lit Frequently Asked Questions Remote Control Maintenance and ServiceMaintenance Tasks-Homeowner Glass Cleaning Venting Porcelain Firebox Panel CleaningMaintenance Tasks-Qualiﬁed Service Technician Gasket Seal and Glass Assembly Inspection IPI Pilot Flame Patterns Burner Ignition and Operation Typical Appliance System Getting Started Design and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Selecting Appliance Location Framing and Clearances Clearances Constructing the Appliance Chase Fireplace Opening Non-Combustible Mantel Vent Termination Minimum Clearances Termination Locations Covered Alcove Applications Install Support Brackets To Install the Heat ShieldContinue Adding Vent Components Use of Elbows Vent Information and DiagramsApproved Pipe Vent Table Key Use of Flex Vent Vent Diagrams Top Vent Horizontal Termination One ElbowV1 Minimum H1 Maximum V1 Minimum H1 + H2 Maximum Top Vent Horizontal Termination Two Elbows V1 Minimum H1 + H2 Maximum V1 + V2 Min Top Vent Horizontal Termination Three Elbows Exhaust restrictor Instructions Two Elbows Three Elbows Minimum Maximum + V 2 MinV1 Minimum Maximum V1 + V2 Min Combustible Wall Penetration Vent Clearances and FramingPipe Clearances to Combustibles Wall Penetration Framing Pipe SLP Install the Ceiling Firestop Install Attic Insulation Shield Flat Ceiling InstallationVaulted Ceiling Installation Securing and Leveling the Appliance Appliance Preparation Assemble Vent Sections Installing Vent Pipe Secure the Vent Sections Assemble Slip Sections Disassemble Vent Sections Install Decorative Ceiling Components Assemble and Install Storm Collar Install Metal Roof Flashing Apply Sealant TOP & Partial Sides Install RF4-8 Install Vertical Termination Cap Install Decorative Wall ComponentsHeat Shield Requirements for Horizontal Termination 22 Venting through the wall Install Horizontal Termination Cap Gas Connection Gas InformationFuel Conversion Gas Pressure Electrical Service and Repair Wiring RequirementsIntelliﬁre Ignition System Wiring Optional Accessories Requirements Intelliﬁre Ignition Wiring Diagram with Remote Receiver Wall Switch Installation for Fan Option Junction Box Installation To install the Splatter Guard FinishingSplatter Guard To Remove the Splatter Guard To Close the Lower Access Panel 15 Non-Combustible Zone Mantel and Wall Projections Combustible Mantel Finishing Material Facing Material Without Front Shown Appliance Setup Air Shutter Setting Install Trim Kits and Surrounds Troubleshooting Symptom Possible Cause Corrective ActionIntelliﬁre Ignition System Remove any contaminants that may have accumulated on Reference Materials Appliance Dimension Diagram Vent Components Diagrams Snorkel Black Support Box-Black Wall Thimble-BlackAdapter SLP-HRC-SS SLP-HRC-ZC-SS Horizontal Termination CAP ST-550TM-IPI Service Parts Service Parts List StockedAt Depot Intermittent Pilot Ignition Valve Assembly Contact Information