Manuals / Hearth and Home Technologies / Kitchen Appliance / Range

Hearth and Home Technologies VRT-BZ-P-CE, VRTIKL-CE Positioning the Logs, Placing Mineral Wool

Models: VRT-GR-P-CE VRT-GR-B-CE VRT-BZ-P-CE VRT-BZ-N-CE VRT-GR-N-CE VRT-GY-B-CE VRT-BZ-B-CE VRT-GY-N-CE VRT-GY-P-CE VRTIKL-CE

1 44

Download 44 pages 45.21 Kb

Page 27

G. Positioning the Logs

While still breakable, the logs do not become fragile until after the gas stove is burned and they have cured. After curing, any handling must be done with care as breakage can easily occur.

PLEASE NOTE: Logs have been designed to work spe- cifically with the burner of this gas stove. Exact place- ment will ensure proper operation of your gas stove.

Figure 8.12

Figure 8.13

Place log #1 into the cradle in the burner. Lean the log back towards right corner of firebox.

Figure 8.14

Locate log #2 over the pin in log #1 and into notch in log #1. Lean the log back toward the left corner of the firebox.

H. Placing Mineral Wool

WARNING

Explosion Risk.

•Follow ember placement instructions in manual.

•Do NOT place embers directly over burner ports.

•Replace ember material annually.

Improperly placed embers interferes with proper burner operation.

Figure 8.17

Apply 1.5 cm size pieces sparingly along ports as shown in Figure 8.17. Do not block ports.

Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07

27

Image 27

Hearth and Home Technologies VRT-BZ-P-CE, VRTIKL-CE, VRT-GY-P-CE, VRT-GY-N-CE Positioning the Logs, Placing Mineral Wool

Contents

What to do if you smell gas Do not Discard this ManualDo Discardnot Serial No Model Name Test Lab Report No Manufactured Date Table of Contents Combustible Materials 1Listing and Code ApprovalsAppliance Certiﬁcation Non-Combustible Materials Design & Installation Considerations Getting StartedInspect Appliance & Components 15.2 25.7 30.8 137.2 91.4 78.1 33.7 39.4 3Appliance Location and ClearancesSelecting Appliance Location Clearances to Combustibles 10.2 78.1 91.4 Optional Stone Surround Installed Flue Termination Minimum Clearances 4Termination Locations Gas stove Alcove Applications Measuring Standards Flue InformationFlue Components Use of Elbows For Natural, Propane and Butane Gases Flueing Diagrams Natural Gas One 90 0 Elbow System Natural Gas Two 90 0 Elbows System Min H1 Max H1 + H2 Max Natural Gas Two 900 Elbows System V1 Min Max Natural Gas Three 90 0 Elbows System Step Horizontal Termination Before YOU Begin Slim Line Wall Thimble FIG. B Minimum Clearance Balance Flue Pipe Vertical Termination Secure Flashing with NON-HARDENING Sealant Roofing Nails Twist-lock the flue cap and seal Vertical Flue Restrictor Gas Information Gas Pressure Requirements Gas ConnectionCheck for GAS Leaks Ignition System Wiring 7Electrical InformationShock Risk Leveling and Bolting Down the Appliance Appliance SetupRemove Shipping Materials Unbolting Appliance from the Pallet Accessories Top to Rear Flue ConversionOn TOP of Appliance On Back of Appliance Installing the Bafﬂe Placing Mineral Wool Positioning the Logs Cap and Barrel Fastener System Before Lighting Appliance Operating Instructions Do not Connect 240 VAC to the Control Valve Lighting the Appliance Frequently Asked Questions Initial Break-in ProcedureAfter Appliance is Lit After servicing Maintaining and Servicing Appliance Inspect Maintenance Tasks Maintenance Tasks Troubleshooting Symptom Possible Causes Corrective ActionsElectronic Ignition System Appliance Dimension Diagram Reference Materials47.9 104.5 103.5 40.3 18.1 76.2 73.3 86.7 75.3 62.0 76.8 42.8 86.7 112.6 Appliance Dimension with Stone Surround Diagram SL-09D SL-12/17D SL-24D SL-36D SL-48D Flue Components Diagram Flue Components List ComponentsTermination Kits Log Set Assembly Service Parts P2B/B2P-VRT-CE Description Serial # Part Number Valve Assembly REM-DLX-CE Warranty Policy Heat & GLO Limited 10 Year Warranty Contact Information Your Records for Model