Manuals / Hearth and Home Technologies / Kitchen Appliance / Range

Hearth and Home Technologies VRT-BZ-B-CE manual 7Electrical Information, A. Ignition System Wiring

Models: VRT-GR-P-CE VRT-GR-B-CE VRT-BZ-P-CE VRT-BZ-N-CE VRT-GR-N-CE VRT-GY-B-CE VRT-BZ-B-CE VRT-GY-N-CE VRT-GY-P-CE VRTIKL-CE

1 44

Download 44 pages 45.21 Kb

Page 23

7Electrical Information

7Electrical Information

A. Ignition System Wiring

•This gas stove is equipped with an electronic ignition system which operates on a 6 volt system.

•The batteries are located within the ignition module which is located behind the glass door assembly. A wiring diagram is shown in Figure 7.1.

•The battery pack requires four AA batteries (not included).

CAUTION

Battery polarity must be correct or module damage will occur.

WARNING

Shock Risk

•Replace damaged wire with type 105° C rated wire.

•Wire must have high temperature insulation.

CAUTION

Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

	FLAME SPARKER/
	SENSOR	VALVE
	PILOT
	IGNITION MODULE	REMOTE
	IGNITION MODULE	CONTROL
	6VDC	ANT.
		ON/OFF
		WALL SWITCH
		IGNITION
		MODULE
		(6V)
	BATTERY PORT
	(4 AA BATTERIES)
		THERMOCOUPLE
		BLOCK
	ON/OFF	(CONNECTED TO
	ON/OFF	BACK OF VALVE)
	SWITCH	BACK OF VALVE)
	SWITCH
		VALVE
	PILOT GAS LINE
	CONNECTED TO
	BACK OF VALVE
	Figure 7.1 Electronic Ignition Wiring Diagram
	Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07	23

Image 23

Hearth and Home Technologies VRT-BZ-B-CE, VRTIKL-CE manual 7Electrical Information, A. Ignition System Wiring, Shock Risk

Contents

Installer’s Guide 0063-06FREESTANDING STOVE What to do if you smell gasPlease retain this owners manual for future reference SAMPLE OF RATINGS LABELRead this manual before installing or operating this gas stove CongratulationsÎ = Contains updated information TABLE OF CONTENTSD. Combustible Materials 1Listing and Code ApprovalsA. Appliance Certiﬁcation C. Non-Combustible MaterialsB. Inspect Appliance & Components A. Design & Installation Considerations2 Getting Started B. Clearances to Combustibles 3Appliance Location and ClearancesA. Selecting Appliance Location 91.4 C. Optional Stone Surround Installed10.2 78.1Maintain ﬂue clearance to combustibles as speciﬁed 4Termination LocationsA. Flue Termination Minimum Clearances Fire Risk. Explosion Riskelectrical service = AREA WHERE TERMINAL IS NOT PERMITTEDpowered air supply inlet trical serviceC. Measuring Standards 5 Flue InformationA. Flue Components B. Use of ElbowsFor Natural, Propane and Butane Gases D. Flueing DiagramsNote For this type of installation, the vertical For Natural, Propane and Butane GasesHeat & Glo VRTIKL-CE 7031-292 Rev E 12/07 Heat & Glo VRTIKL-CE 7031-292 Rev E 12/07 Heat & Glo VRTIKL-CE 7031-292 Rev E 12/07 V2 V1 HHeat & Glo VRTIKL-CE 7031-292 Rev E 12/07 Step E. Horizontal TerminationStep Step1. Assembling Slim Line Trim Ring and Heat Shield F. Slim Line Wall Thimble BEFORE YOU BEGIN2. Installing Slim Line Trim Ring and Heat Shield MINIMUM OF 152 mm OF PIPE THROUGH THE WALL INTERIOR WALL FIG. B MINIMUM CLEARANCECENTER LINE USE HEAT SHIELD / WALL THIMBLE Place mark where protrudes throughStep G. Vertical Termination1. Balance Flue Pipe StepStep StepSECURE FLASHING WITH NON-HARDENING SEALANT AND ROOFING NAILS StepStep H. Vertical Flue RestrictorFire Risk Explosion Risk 6 Gas InformationA. Gas Pressure Requirements B. Gas ConnectionShock Risk A. Ignition System Wiring7Electrical Information C. Leveling and Bolting Down the Appliance 8 Appliance SetupA. Remove Shipping Materials B. Unbolting Appliance from the PalletINNER EXTENSION COLLAR DV ADAPTER ALLEN HEAD SCREWS D. AccessoriesE. Top to Rear Flue Conversion ON TOP OF APPLIANCEON TOP OF APPLIANCE F. Installing the BafﬂeON BACK OF APPLIANCE INNER EXTENSION COLLARDo NOT place embers directly over burner ports G. Positioning the LogsH. Placing Mineral Wool Explosion Risk Follow ember placement instructions in manualJ. Inner Glass Door Assembly Replacement I. Front Door Glass Assembly InstallationGlass replacement should be done by qualiﬁed technician 9 Operating InstructionsA. Before Lighting Appliance Glass door must be in place when gas stove is operating Risk ofB. Lighting the Appliance FOR YOUR SAFETY READ BEFORE LIGHTINGLIGHTING INSTRUCTIONS TO TURN OFF GAS TO APPLIANCEC. After Appliance is Lit D. Frequently Asked QuestionsISSUE SOLUTIONSBurner air shutter adjustment Gas connections and ﬁttings 10 Maintaining and Servicing ApplianceReseal and reinstall any venting removed for servicing Condition of glass, glass assembly and glass sealInspect A. Maintenance TasksMaintenance Tasks Possible Causes 11 TroubleshootingElectronic Ignition System SymptomHearth Pad A. Appliance Dimension Diagram12 Reference Materials E F G62.0 B. Appliance Dimension with Stone Surround DiagramHearth Pad 75.3SL-90D C. Flue Components DiagramSL-45D SL-17/24DSL-12D SL17-24DTERMINATION KITS D. Flue Components ListCOMPONENTS Service Parts Diagram Service PartsLog Set Assembly VRTIKL-CESERIAL # E. Service PartsVRTIKL-CE DESCRIPTIONPilot Assembly N Valve AssemblyService Parts Valve Assembly Parts ListSERIAL # Service PartsVRTIKL-CE DESCRIPTIONF. Warranty Policy HEAT & GLO LIMITED 10 YEAR WARRANTYDATE INSTALLED Your Records for ModelG. Contact Information DEALERSHIP WHERE PURCHASED