Venting with Three 3 90 Elbows | Heat & Glo LifeStyle 8000TRD

VENTING WITH THREE (3) 90° ELBOWS

V	H	H + H1
1´MIN. (305mm)	2´MAX. (610mm)	5´MAX. (1.52m)
2´MIN. (610mm)	4´MAX. (1.22m)	10´MAX. (3.1m)
3´MIN. (914mm)	6´MAX. (1.86m)	15´MAX. (4.65m)
4´MIN. (1.22m)	8´MAX. (2.48m)	20´MAX. (6.2m)

V1+V+H+H1 = 40´ MAX.(12.4 m) H = 8´MAX.(2.48 m) H+H 1 = 20´MAX.(6.2 m)

H + H1 + H2

1´MIN. (305mm)

2´MAX. (610mm)

5´MAX. (1.52m)

2´MIN.

(610mm)

4´MAX. (1.22m)

10´MAX. (3.1m)

3´MIN.

(914mm)

6´MAX. (1.86m)

15´MAX. (4.65m)

4´MIN.

(1.22m)

8´MAX. (2.48m)

20´MAX. (6.2m)

V+H+H1+H2 = 40´ MAX. (12.4 m)

H = 8´ MAX. (2.48 m)

H+H 1+H2 = 20´ MAX. (6.2 m)

Figure 16. Venting with three 90° elbows

Page 18

Image 18

Heat & Glo LifeStyle 8000TRD manual Venting with Three 3 90 Elbows, Venting with three 90 elbows

Contents

Installers Guide What to do if you smell gas Safety and Warning Information Table of Contents 18 9 Log Set Assembly 8000TRD Standing Pilot Ignition / D’ALLUMAGE PAR Veilleuse Service Parts List / Liste des pièces de rechange 8000TRDCommon Parts / Piéces Communes IPI Ignition Allumage IPI Appliance Certification Installation CodesHigh Altitude Installations Certification Pre-install Preparation Introducing the Heat-N-Glo Gas FireplacesANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the 8000TRD Clearance Requirements Constructing the Fireplace ChaseLocating the Fireplace Space Requirements Framing Dimensions Framing the Fireplace 187mm 149mm 220mm DV-90D 164mm 216mm Identifying Vent Components Installing the Vent SystemVent System Approvals Terminations Kits MAX .4 M Flue Restrictor InstructionsVertical Venting Break Here Chart Venting with ONE 1 90 Elbow Venting with One 90 Elbow Venting with TWO Elbows MIN MAX mm 610mm MAX .22m 914mm MAX .86m MAX .4m Venting with Three 3 90 Elbows Venting with three 90 elbows + H 1 FT Installing Vent Components Stove Cement Must be Placed around5 Inch 127 MM Fireplace Starting COL To Install the Heat Shield Install Support BracketsContinue Adding Vent Components 12 Hole and Vent Pipe Vent Termination Positioned SO That the Arrow is Pointing UP4 184mm Vent Termination Minimum Clearances Minimum Height from Roof to Lowest Discharge Opening Gas Control Systems Vice Must be Wired Directly to the FIRE- Place Junction BOXPositioning, Leveling, and Securing the Fireplace Standing Pilot Ignition System Check for GAS Leaks Gas Supply LineGas Pressure Requirements Natural Gas Propane Optional fan and remote control kits require that Wiring the FireplaceOptional Accessories Position the wall switch in the desired position on a wall Operation using Battery Power Black Optional Battery BACK-UP RED Brown Finishing Sealant Material Hearth Extensions Shutter Settings Burner Placing the Ember Material Installing Trim, Logs, and Ember MaterialInstalling the Trim Outlet Grilles in ANY Manner Double-check for faulty components After the InstallationGlass Specifications 8000TRD 26 1/2 X 42 1/2 Tempered Before Lighting the Fireplace Important Turn OFF the GAS Before Servicing Your Fireplace Fireplace MaintenanceCleaning Glass Door Replacing old ember material