+ H 1 FT | Heat & Glo LifeStyle 8000TRD guide

	VENTING WITH THREE (3) 90° ELBOWS
V (FT.)	H (FT.)	H
1' MIN. (305mm)	5' MAX. (1.52m)	H
1' MIN. (305mm)	5' MAX. (1.52m)
2' MIN. (610mm)	10' MAX. (3.1m)
3' MIN. (914mm)	15' MAX. (4.65m)
4' MIN. (1.22m)	20' MAX. (6.2m)
NOTE: H + H1 = 20' MAX. (6.2m)
V + V1 + H + H1= 40' MAX. (12.4m)
	H1
	V1

V (FT.)	H	+ H1 (FT.)
1' MIN. (305mm)	5'	MAX. (1.52m)
2' MIN. (610mm)	10'	MAX. (3.1m)
3' MIN. (914mm)	15'	MAX. (4.65m)
4' MIN. (1.22m)	20'	MAX. (6.2m)

H +H1 = 20' MAX. (6.2m)

NOTE: V+V1+H +H1 = 40' MAX. (12.4m)

Figure 17. Venting with three 90° elbows

Page 19

Image 19

Heat & Glo LifeStyle 8000TRD manual + H 1 FT

Contents

What to do if you smell gas Installers Guide Safety and Warning Information Table of Contents 8000TRD 18 9 Log Set Assembly IPI Ignition Allumage IPI Service Parts List / Liste des pièces de rechange 8000TRDCommon Parts / Piéces Communes Standing Pilot Ignition / D’ALLUMAGE PAR Veilleuse Certification Installation CodesHigh Altitude Installations Appliance Certification Introducing the Heat-N-Glo Gas Fireplaces Pre-install PreparationANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the 8000TRD Space Requirements Constructing the Fireplace ChaseLocating the Fireplace Clearance Requirements Framing the Fireplace Framing Dimensions 187mm 149mm 220mm DV-90D 164mm 216mm Terminations Kits Installing the Vent SystemVent System Approvals Identifying Vent Components Break Here Flue Restrictor InstructionsVertical Venting MAX .4 M Chart Venting with One 90 Elbow Venting with ONE 1 90 Elbow Venting with TWO Elbows MIN MAX mm 610mm MAX .22m 914mm MAX .86m MAX .4m Venting with three 90 elbows Venting with Three 3 90 Elbows + H 1 FT Stove Cement Must be Placed around Installing Vent Components5 Inch 127 MM Fireplace Starting COL Install Support Brackets To Install the Heat ShieldContinue Adding Vent Components 12 Hole and Vent Pipe Positioned SO That the Arrow is Pointing UP Vent Termination4 184mm Vent Termination Minimum Clearances Minimum Height from Roof to Lowest Discharge Opening Standing Pilot Ignition System Vice Must be Wired Directly to the FIRE- Place Junction BOXPositioning, Leveling, and Securing the Fireplace Gas Control Systems Natural Gas Propane Gas Supply LineGas Pressure Requirements Check for GAS Leaks Position the wall switch in the desired position on a wall Wiring the FireplaceOptional Accessories Optional fan and remote control kits require that Black Optional Battery BACK-UP RED Brown Operation using Battery Power Sealant Material Hearth Extensions Finishing Outlet Grilles in ANY Manner Installing Trim, Logs, and Ember MaterialInstalling the Trim Shutter Settings Burner Placing the Ember Material Before Lighting the Fireplace After the InstallationGlass Specifications 8000TRD 26 1/2 X 42 1/2 Tempered Double-check for faulty components Replacing old ember material Fireplace MaintenanceCleaning Glass Door Important Turn OFF the GAS Before Servicing Your Fireplace

VENTING WITH THREE (3) 90° ELBOWS

+ H1 (FT.)

Figure 17. Venting with three 90° elbows