Heat & Glo LifeStyle 8000TRD specification

VENTING WITH TWO (2) 90o ELBOWS

V FT.	(305mm)	H + H1 (FT.)
1' MIN.	(305mm)	2' MAX. (610mm)
2' MIN.	(610mm)	4' MAX. (1.22m)
3' MIN.	(914mm)	6' MAX. (1.86m)
4' MIN.	(1.22m)	8' MAX. (2.4m)
V+H+H1= 40' MAX. (12.4m)		H+H1= 8' MAX. (2.4m)

Figure 15. Venting with Two 90° Elbows

Page 17

Image 17

Heat & Glo LifeStyle 8000TRD manual MIN MAX mm 610mm MAX .22m 914mm MAX .86m MAX .4m

Contents

What to do if you smell gas Installers Guide Safety and Warning Information Table of Contents 8000TRD 18 9 Log Set Assembly Common Parts / Piéces Communes Service Parts List / Liste des pièces de rechange 8000TRDStanding Pilot Ignition / D’ALLUMAGE PAR Veilleuse IPI Ignition Allumage IPI High Altitude Installations Installation CodesAppliance Certification Certification ANY Such Action MAY Possibly Cause a Fire Hazard Pre-install PreparationIntroducing the Heat-N-Glo Gas Fireplaces Diagram of the 8000TRD Locating the Fireplace Constructing the Fireplace ChaseClearance Requirements Space Requirements Framing the Fireplace Framing Dimensions 187mm 149mm 220mm DV-90D 164mm 216mm Vent System Approvals Installing the Vent SystemIdentifying Vent Components Terminations Kits Vertical Venting Flue Restrictor InstructionsMAX .4 M Break Here Chart Venting with One 90 Elbow Venting with ONE 1 90 Elbow Venting with TWO Elbows MIN MAX mm 610mm MAX .22m 914mm MAX .86m MAX .4m Venting with three 90 elbows Venting with Three 3 90 Elbows + H 1 FT 5 Inch 127 MM Fireplace Starting COL Installing Vent ComponentsStove Cement Must be Placed around Continue Adding Vent Components To Install the Heat ShieldInstall Support Brackets 12 Hole and Vent Pipe 4 184mm Vent TerminationPositioned SO That the Arrow is Pointing UP Vent Termination Minimum Clearances Minimum Height from Roof to Lowest Discharge Opening Positioning, Leveling, and Securing the Fireplace Vice Must be Wired Directly to the FIRE- Place Junction BOXGas Control Systems Standing Pilot Ignition System Gas Pressure Requirements Gas Supply LineCheck for GAS Leaks Natural Gas Propane Optional Accessories Wiring the FireplaceOptional fan and remote control kits require that Position the wall switch in the desired position on a wall Black Optional Battery BACK-UP RED Brown Operation using Battery Power Sealant Material Hearth Extensions Finishing Installing the Trim Installing Trim, Logs, and Ember MaterialShutter Settings Burner Placing the Ember Material Outlet Grilles in ANY Manner Glass Specifications 8000TRD 26 1/2 X 42 1/2 Tempered After the InstallationDouble-check for faulty components Before Lighting the Fireplace Cleaning Glass Door Fireplace MaintenanceImportant Turn OFF the GAS Before Servicing Your Fireplace Replacing old ember material

VENTING WITH TWO (2) 90o ELBOWS

H + H1 (FT.)

1' MIN.

2' MAX. (610mm)

(610mm)

4' MAX. (1.22m)

(914mm)

6' MAX. (1.86m)

8' MAX. (2.4m)

Figure 15. Venting with Two 90° Elbows