Removing Access Door
and Battery
598-1116-10

Add-A-Switch

Installation

1.Remove Tab from Battery Chamber. Remove cover from front of Add-A-Switch transmitter. Gently pull tab out of battery chamber. Slide cover ontoAdd-A-Switch transmitter.

Add-A-Switch

DIM

ON/OFFButton

Button

Battery Chamber

(Type CR2032)

 

 

Tab

3V

um Batter

2032

y

Access Door

DIM

Access Door

Add-A-Switch

Removing Battery Tab

2.Selectmountinglocationforadd-a-switchtransmitter.Note:Trans- mitter should be located within 100 feet (30 m) of receiver. Note: Transmitter should be mounted approximately 4 feet from the floor and in the vertical position.

3.Before mounting, hold transmitter in selected location and verify operation (see Operation). Note: If transmitter does not operate correctly, see Troubleshooting Guide.

4.With transmitter held in place, mark the mounting holes with a pencil or pointed object.

5.Remove transmitter and drill two 3/16” holes. Tap drywall anchors (provided) into holes with a hammer.

6.Attach transmitter to wall using two screws (provided).

Operation

1.Verify that receiver has been properly installed. See Receiver Information, page 7.

2.Push the ON (top) button and release. The light should turn on full bright.

3.Push the OFF (bottom) button and release. The light should turn off.

4.Push the DIM button and release. The light should turn on at a DIM level.

5.Continue to press the DIM button until the desired dim level is reached. Note: Receiver remembers last DIM setting used. To recall last DIM setting, push and release the DIM button.

Note: The DIM setting defaults to 50% in the event of a power failure.

Important: Wait 1 to 2 seconds after you press a transmitter button before you press it again to allow the transmission to be completed.

Note: If light does not turn on or intermittently turns on and off when transmitter buttons are pushed, see Troubleshooting Guide.

Battery Replacement

The wall switch transmitter requires a type CR2032, 3-volt lithium battery to operate. The transmitter is shipped with the battery installed. With typical use, the battery will last approximately 5 years. Remove battery when transmitter will not be used for an extended period of time.

1.

Place thumb on access door

 

 

 

and slide down to open.

 

 

Battery

2.

Carefully bend locking

tab

 

 

Locking

 

outward. Battery will

pop

DIM

 

 

Tab

 

up.

 

 

 

 

 

 

3.

Remove battery from sock-

 

ium Batter

 

et.

 

 

3V 2032 y

 

 

 

 

4.

Install replacement battery in

 

 

 

socket plus (+) side up (see

Access

CR2032

 

illustration). Press down on

Door

 

Lithium

 

battery until locking tab snaps

 

 

 

Battery

 

into place.

 

 

 

 

 

 

5.

Reinstall access door

by

 

 

sliding it upward until it locks in place.



Page 3 Page 5
Page 4
Image 4
Heath Zenith 598-1116-10 Installation, Operation, Battery Replacement, Add-A-Switch Removing Battery Tab
Page 3 Page 5

598-1116-10 specifications

The Heath Zenith 598-1116-10 is an advanced motion-sensing outdoor light designed to enhance security and functionality around homes and businesses. This fixture is engineered with the latest technologies to provide reliable performance while ensuring energy efficiency and ease of use.

One of the main features of the 598-1116-10 is its state-of-the-art motion sensor. The device employs a passive infrared (PIR) technology that detects movement within a significant range, ensuring that any motion in its monitored area triggers the light. The sensor is adjustable, allowing users to customize the detection range and sensitivity to suit their specific environment. This adaptability is crucial for minimizing false alarms from unwarranted movements, such as passing cars or animals.

In addition to its motion-detection capabilities, the Heath Zenith 598-1116-10 offers various lighting options. The fixture is equipped with a powerful LED light source that produces a bright output while consuming less energy than traditional incandescent bulbs. This not only aids in lowering electricity costs but also contributes to a longer lifespan for the light, reducing the frequency and hassle of bulb replacements.

The design of the 598-1116-10 reflects both aesthetic appeal and functional robustness. The weather-resistant construction ensures that the light can withstand various climatic conditions, making it suitable for installation in different outdoor environments. The sleek and modern design complements a wide range of architectural styles, enhancing the property’s overall curb appeal.

Another important characteristic of this outdoor security light is its convenient operating features. The device includes a manual override option, allowing homeowners to keep the light on continuously for extended periods when needed, such as during gatherings or outdoor events. Additionally, the light can be set to operate on a timer, providing flexibility and control over illumination schedules.

In conclusion, the Heath Zenith 598-1116-10 stands out in the outdoor lighting market due to its motion-sensing technology, energy-efficient LED lighting, durable design, and user-friendly features. It serves not only as a means of illumination but also as a crucial security element, helping to deter potential intruders while offering peace of mind for property owners. This combination of practicality and style makes the 598-1116-10 a top choice for those looking to enhance their outdoor lighting system.
Top Page Image Contents