Receiver Information, Gang | Heath Zenith 598-1135-08 manual

Receiver Information

All receivers have the following features and ratings:

•Rated for 120VAC/60Hz supply voltage.

•Uses existing wiring.

•Fits standard single gang junction box.

•Up to 100 feet (30 m) typical transmission range.

•When first turned on wait 15 seconds.

Wall Switch Receiver

Features and Ratings:

• Up to 500 Watt maximum incandescent load depend- ing upon switch purchased. See rating label on switch for exact load rating.

• Not for use with Compact Fluorescent bulbs.

WARNING: FOR USE ONLY with 120 volt incandescent or halogen bulbs.

CAUTION: To reduce the risk of overheating and pos- sible damage to other equipment, do not install to control a receptacle, a motor-operated appliance, a fluorescent lighting fixture, or a transformer-supplied appliance.

ImportantInformationRegarding3-WaySwitchInstallations:

In order to use this product where two switches are being used to control the light, the 3-Way Wall Switch transmitter will also have to be installed. Refer to the 3-Way Wall Switch Installation section for details.

Important: When ganging these units, they must be derated as follows:

Gang	1	2	3

300 W	300 W	300 W	300 W
500 W	500 W	475 W	450 W
500 W	500 W	475 W	450 W

Installation

1.Select light switch to be replaced by wall switch receiver.

2.WARNING:Turn off the power to the light switch circuit before you proceed. Do this at your circuit breaker or fuse box.

3.Remove the existing wall plate and switch. Disconnect the two power wires and the ground wire.

Note: If there are more than two power wires attached to the switch, consult an electrician about installation.In addition, some local build- ing codes may require installation by a qualified electrician.

CAUTION: Do not connect neutral (white wire) to switch.

4.If necessary, strip away 1/2" of insulation from end of wires.

5.Connect one of the black power wires from receiver to one of the power wires you removed from the old switch. Use one of the supplied wire connectors to secure the wires (see illustration).

6.Connect the second black power wire from receiver to the other power wire you removed from the old switch. Use one of the supplied wire connectors to secure the wires (see illustration).

7.Connect the green ground wire from receiver to the ground wire removed from old switch. Use one of the supplied wire connectors to secure the wires (see illustration).

8.Check wire connections to make sure they are secure and that no bare wires are exposed.

9.Route antenna between the bottom of the junction box and the wall. Feed antenna into wall cavity while placing wall switch into junction box.

10.Position the wall switch receiver in the junction box with the DIM button located to the right. Use the two wall switch screws (long) supplied to mount the receiver to the wall box (see illustration). Push excess wiring into wall box while you do this. You may need to bend the wires to fit inside the box. Mount wall plate on wall switch receiver with screws (short) provided.

11.Turn on the power to the light switch circuit. Do this at your circuit breaker or fuse box.

Ground Wire (Bare or Green)

		Junction Box
		Wall
	ON/OFF Button	Switch
	Wall Switch Screw	White
		White
	Wall Plate	(Neutral)
	Wall Plate
	Screw
		Wall
	Wall Plate	DIM Button
	Wall Plate	Antenna
		Antenna
		Power Disconnect Switch

Installing Wall Switch Receiver

Operation

1.Verify the power disconnect switch is in the ON (right side) position.

2.Push the ON (top) button and release. The light should turn on full bright. Note: If you are controlling a lamp, make sure it is connected to the switched outlet and the lamp is switched on.

3.Push the OFF (bottom) button and release. The light should turn off.

10	598-1135-08

598-1135-08 specifications

The Heath Zenith 598-1135-08 is a state-of-the-art motion-activated floodlight designed to enhance security and visibility around your home or property. With its durable construction and advanced technological features, this floodlight offers an efficient solution for outdoor lighting needs.

One of the key aspects of the Heath Zenith 598-1135-08 is its reliable motion detection technology. Featuring a high-performance sensor, this floodlight can detect movement within a wide range, typically up to 240 degrees. This expansive field of view ensures that any activity within its range is promptly detected, providing an added layer of security for your belongings and family.

The floodlight also boasts an impressive illumination capacity. Equipped with powerful LED bulbs, it delivers bright, energy-efficient lighting that can easily illuminate large outdoor areas. The LED technology not only ensures a longer lifespan for the bulbs but also significantly reduces energy consumption, making it an environmentally friendly choice.

Another notable characteristic is the adjustable settings available with the Heath Zenith 598-1135-08. Users can easily customize the sensitivity of the motion sensor, allowing it to adapt to specific needs such as varying outdoor conditions or traffic levels. Additionally, the floodlight offers a time delay feature, permitting the light to stay on for a designated period after motion is detected, providing extra convenience.

The design of the Heath Zenith 598-1135-08 combines functionality with aesthetic appeal. The sleek, modern look of the floodlight makes it suitable for various types of homes and outdoor settings. Moreover, its weather-resistant construction ensures that it can withstand harsh weather conditions, maintaining its performance throughout the seasons.

Installation of the Heath Zenith 598-1135-08 is straightforward, making it accessible for homeowners looking to enhance their outdoor lighting without professional assistance. The adjustable head allows for directional lighting, ensuring that specific areas can be spotlighted as needed.

Overall, the Heath Zenith 598-1135-08 is an exemplary choice for homeowners seeking robust, energy-efficient outdoor lighting solutions. Its combination of advanced motion detection technology, customizable settings, and durable design makes it a valuable addition for increased security and visibility around any property.

Heath Zenith 598-1135-08 operating instructions Receiver Information, Wall Switch Receiver, Gang

Models: 598-1135-08