Manuals / Heath Zenith / TV and Video / Universal Remote

Heath Zenith 598-1135-08 Add-A-Switch, Kid’s Remote Control, Installation, Operation

Models: 598-1135-08

1 44
Download 44 pages 33.17 Kb
Page 7
Image 7

Add-A-Switch

Installation

1. Remove Tab from Battery Chamber. Remove cover from front of Add-A-Switch transmitter. Gently pull tab out of battery chamber.Slide cover onto Add-A-Switch transmitter.

 

 

Tab

3V

um Batter

2032

y

Battery Chamber

 

 

(Type CR2032)

 

 

Access Door

Removing Battery Tab

2.Selectmountinglocationforadd-a-switchtransmitter.Note:Trans- mitter should be located within 100 feet (30 m) of receiver. Note:Transmitter should be mounted approximately 4 feet from the floor and in the vertical position.

3.Before mounting, hold transmitter in selected location and verify operation (see Operation). Note: If transmitter does not operate correctly, see Troubleshooting Guide.

4.With transmitter held in place, mark the mounting holes with a pencil or pointed object.

5.Remove transmitter and drill two 3/16" holes. Tap drywall anchors (provided) into holes with a hammer.

6.Attach transmitter to wall using two screws (provided).

Operation

1.Verify that receiver has been properly installed. See Receiver Information, page 10.

2.Push the ON (top) button and release.The light should turn on full bright.

3.Push the OFF (bottom) button and release. The light should turn off.

4.Push the DIM button and release. The light should turn on at a DIM level.

Add-A-Switch

DIM

ON/OFFButton

Button

DIM

Access Door

Add-A-Switch

5.Continue to press the DIM button until the desired dim level is reached. Note: Receiver remembers last DIM setting used. To recall last DIM setting, push and release the DIM button.

Note: The DIM setting defaults to 50% in the event of a power failure.

Important: Wait 1 to 2 seconds after you press a transmitter button before you press it again to allow the transmission to be completed.

Note: If light does not turn on or intermittently turns on and off when transmitter buttons are pushed, see Troubleshooting Guide.

Battery Replacement

The wall switch transmitter requires a type CR2032, 3-volt lithium

ENGLISH

battery to operate. The transmitter is shipped with the battery

installed. With typical use, the battery will last approximately 5

years. Remove battery when transmitter will not be used for an

extended period of time.

 

 

 

1. Place thumb on access door

 

Battery

 

and slide down to open.

DIM

Locking

 

2. Carefully bend locking tab

 

Tab

 

outward. Battery will pop up.

 

 

 

3. Remove battery from socket.

 

ium Ba

 

 

tter

 

 

3V 2032 y

 

4. Install replacement battery in

 

 

 

socket plus (+) side up (see

Access

CR2032

 

illustration). Press down on

 

Door

 

battery until locking tab snaps

Lithium

 

 

 

into place.

 

Battery

 

5. Reinstall access door by

 

sliding it upward until it locks

Removing Access Door

in place.

and Battery

 

Kid’s Remote Control

Operation

1.Verify that receiver has been properly installed. See Receiver Information, page 10.

Remote Control

Back

Philips-Head

Screw

Access

Door

Removing Access Door

598-1135-08

Page 6 Page 8
Page 7
Image 7
Heath Zenith 598-1135-08 Add-A-Switch, Kid’s Remote Control, Installation, Operation, Battery Replacement
Page 6 Page 8

598-1135-08 specifications

The Heath Zenith 598-1135-08 is a state-of-the-art motion-activated floodlight designed to enhance security and visibility around your home or property. With its durable construction and advanced technological features, this floodlight offers an efficient solution for outdoor lighting needs.

One of the key aspects of the Heath Zenith 598-1135-08 is its reliable motion detection technology. Featuring a high-performance sensor, this floodlight can detect movement within a wide range, typically up to 240 degrees. This expansive field of view ensures that any activity within its range is promptly detected, providing an added layer of security for your belongings and family.

The floodlight also boasts an impressive illumination capacity. Equipped with powerful LED bulbs, it delivers bright, energy-efficient lighting that can easily illuminate large outdoor areas. The LED technology not only ensures a longer lifespan for the bulbs but also significantly reduces energy consumption, making it an environmentally friendly choice.

Another notable characteristic is the adjustable settings available with the Heath Zenith 598-1135-08. Users can easily customize the sensitivity of the motion sensor, allowing it to adapt to specific needs such as varying outdoor conditions or traffic levels. Additionally, the floodlight offers a time delay feature, permitting the light to stay on for a designated period after motion is detected, providing extra convenience.

The design of the Heath Zenith 598-1135-08 combines functionality with aesthetic appeal. The sleek, modern look of the floodlight makes it suitable for various types of homes and outdoor settings. Moreover, its weather-resistant construction ensures that it can withstand harsh weather conditions, maintaining its performance throughout the seasons.

Installation of the Heath Zenith 598-1135-08 is straightforward, making it accessible for homeowners looking to enhance their outdoor lighting without professional assistance. The adjustable head allows for directional lighting, ensuring that specific areas can be spotlighted as needed.

Overall, the Heath Zenith 598-1135-08 is an exemplary choice for homeowners seeking robust, energy-efficient outdoor lighting solutions. Its combination of advanced motion detection technology, customizable settings, and durable design makes it a valuable addition for increased security and visibility around any property.