WAY Wall Switch Transmitter | Heath Zenith 598-1135-08 specs

2.To remove tab from battery chamber, remove screw in access door of remote with a small phillips-head screwdriver. Gently pull tab out of battery chamber. Reassemble access door in reverse order.

Tab

12V

Removing Tab In Battery Chamber

3.Push and release the ON button (left button) to turn light on or the OFF button (right button) to turn light off. Note: Red light on remote should come on while button is depressed.

Important: Wait 1 to 2 seconds after you press a transmitter

3-WAY WALL SWITCH TRANSMITTER

Important: This product must be used in conjunction

with the Wall Switch Receiver. 3-way circuit wiring is

required to install and use this product.

Note: If you are not familiar with electrical wiring, consult an electrician about installation. In addition, some local building codes may require installation by a qualified electrician.

Installation

1.Select light switch to be replaced by 3-way wall switch transmit- ter.

2. WARNING:Turn off the power to the light switch circuit before you proceed. Do this at your circuit breaker or fuse box.

3.Remove the existing wall plate and switch. Label the wires on the existing switch according to the diagram in Figure 1. Note: Typical 3-way wiring is shown. Actual wiring and wire colors may vary.

button before you press it again to allow the transmission to be completed.

Note: If light does not turn on or intermittently turns on and off when remote buttons are pushed, see Troubleshooting Guide.

Battery Replacement

The remote control requires a type A23 12 Volt alkaline battery to operate. The remote control is shipped with the battery installed. With typical use, the battery will last approximately one year. Remove battery when remote will not be used for an extended period of time.

To replace the battery, follow the instructions below:

1.	Turn remote control upside down.
2.	Remove screw in access door of remote with a small phillips-
	head screwdriver.

Common Terminal

(Dark Screw)

TO HOT	1

OR LIGHT BLACK

3-Way Switch

RED

Travel Wire

BLACK

GREEN

(Ground)

4 BLACK	TO HOT
	TO HOT
	OR LIGHT

3-Way Switch

Travel

Wire

3.	Remove access door and lay aside.
4.	Remove battery.Install replacement battery.Make sure battery
	is oriented properly (see illustration).
5.	Reassemble access door in reverse order.

Battery
Compartment	ON
(Type A23)

12V

Inside of Remote Control

Figure 1 - Typical 3-Way Wiring

4.Disconnect the two travel wires, wire connected to common terminal, and the ground wire.

5.Remove the wall plate from the 3-way wall switch transmitter.

WARNING: The white neutral wires in a 3-way circuit must run continuously through the entire circuit. If pres- ent, do not connect a white neutral wire to either of the 3-way switch wires.

6.Connect the wires of the 3-way wall switch transmitter to the wires in the junction box as shown in Figure 2. Use the supplied wire connectors to secure the wires (see Figure 2).Note: Either black wire on the transmitter can be used to connect to the hot wire (light) or traveler wire.

7.Connect the green ground wire from transmitter to the ground wire removed from old switch. Use one of the supplied wire connectors to secure the wires (see Figure 3).

8.Check wire connections to make sure they are secure and that no bare wires are exposed.

598-1135-08

598-1135-08 specifications

The Heath Zenith 598-1135-08 is a state-of-the-art motion-activated floodlight designed to enhance security and visibility around your home or property. With its durable construction and advanced technological features, this floodlight offers an efficient solution for outdoor lighting needs.

One of the key aspects of the Heath Zenith 598-1135-08 is its reliable motion detection technology. Featuring a high-performance sensor, this floodlight can detect movement within a wide range, typically up to 240 degrees. This expansive field of view ensures that any activity within its range is promptly detected, providing an added layer of security for your belongings and family.

The floodlight also boasts an impressive illumination capacity. Equipped with powerful LED bulbs, it delivers bright, energy-efficient lighting that can easily illuminate large outdoor areas. The LED technology not only ensures a longer lifespan for the bulbs but also significantly reduces energy consumption, making it an environmentally friendly choice.

Another notable characteristic is the adjustable settings available with the Heath Zenith 598-1135-08. Users can easily customize the sensitivity of the motion sensor, allowing it to adapt to specific needs such as varying outdoor conditions or traffic levels. Additionally, the floodlight offers a time delay feature, permitting the light to stay on for a designated period after motion is detected, providing extra convenience.

The design of the Heath Zenith 598-1135-08 combines functionality with aesthetic appeal. The sleek, modern look of the floodlight makes it suitable for various types of homes and outdoor settings. Moreover, its weather-resistant construction ensures that it can withstand harsh weather conditions, maintaining its performance throughout the seasons.

Installation of the Heath Zenith 598-1135-08 is straightforward, making it accessible for homeowners looking to enhance their outdoor lighting without professional assistance. The adjustable head allows for directional lighting, ensuring that specific areas can be spotlighted as needed.

Overall, the Heath Zenith 598-1135-08 is an exemplary choice for homeowners seeking robust, energy-efficient outdoor lighting solutions. Its combination of advanced motion detection technology, customizable settings, and durable design makes it a valuable addition for increased security and visibility around any property.

Heath Zenith 598-1135-08 WAY Wall Switch Transmitter, Removing Tab In Battery Chamber

Models: 598-1135-08