Heatiator IDV4833IT owner manual Table of Contents, Safety Alert Key, User Guide, Installer Guide

Safety Alert Key:

•DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.

•WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.

•CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

•NOTICE: Used to address practices not related to personal injury.

Table of Contents

A.	Congratulations	2	A.	Approved Pipe	22
B.	Limited Lifetime Warranty	5	B.	Vent Table Key	22
1 Listing and Code Approvals			C.	Use of Elbows	22
			D.	Measuring Standards	22
A.	Appliance Certification	7
			E.	Vent Diagrams	23
B.	Tempered Glass Specifications	7
			8 Vent Clearances and Framing
C.	BTU Specifications	7
D.	High Altitude Installations	7	A.	Pipe Clearances to Combustibles	28
E.	Non-Combustible Materials Specification	7	B.	Wall Penetration Framing	28
F.	Combustible Materials Specification	7	C.	Install the Ceiling Firestop	29
G.	Electrical Codes	7	D.	Install Attic Insulation Shield	30
H.	Requirements for the Commonwealth		9 Appliance Preparation
	of Massachusetts	8
			A.	Secure and Level the Appliance	31

User Guide

2 Operating Instructions

A.	Gas Fireplace Safety	9
B.	Your Fireplace	9
C.	Clear Space	10
D. Decorative Doors and Fronts		10
E.	Fixed Glass Assembly	10

F.Remote Controls, Wall Controls and Wall Switches10

	G.	Before Lighting Fireplace	10
	H.	Lighting Instructions (IPI)	11
	I.	After Fireplace is Lit	12
	J.	Flame Adjustment Control	12
	K.	Frequently Asked Questions	12
	3 Maintenance and Service
	A.	Maintenance Tasks-Homeowner	13
	B.	Maintenance Tasks-Qualified Service Technician	14

Installer Guide

4 Getting Started
A.	Typical Appliance System	15
B.	Design and Installation Considerations	16
C. Tools and Supplies Needed		16
D. Inspect Appliance and Components		16

5 Framing and Clearances
A.	Select Appliance Location	17
B.	Construct the Appliance Chase	18
C.	Clearances	18
D.	Mantel and Wall Projections	19

6	Termination Locations
	A. Vent Termination Minimum Clearances	20
7	Vent Information and Diagrams

10 Install Vent Pipe

A.	Assemble Vent Sections	32
B.	Assemble Slip Sections	33
C.	Secure the Vent Sections	33
D.	Disassemble Vent Sections	34
E.	Install Metal Roof Flashing	34
F.	Assemble and Install Storm Collar	35
G.	Install Vertical Termination Cap	36
H.	Heat Shield Requirements for Horizontal
	Termination	36
I.	Install Horizontal Termination Cap	37

11 Shrouds

A.	HHT Shrouds	38
B.	Field Constructed Shrouds	38

12 Gas Information

A.	Fuel Conversion	40
B.	Gas Pressure	40
C.	Gas Connection	40
D.	High Altitude Installations	40

13 Electrical Information

A.	Wiring Requirements	41
B. Intellifire Ignition System Wiring		41
C.	Optional Accessories Requirements	41
D. Electrical Service and Repair		41
E.	Junction Box Installation	42

14 Finishing

A.	Mantel and Wall Projections	43
B.	Facing Material	43
C.	Non-combustible Finishing Material	44

15 Appliance Setup

A.	Remove Shipping Materials	45
B.	Remove Fixed Glass Assembly	45
C. Remove Materials Shipped Inside Firebox		45
D.	Clean the Appliance	45
E.	Accessories	45

Heatilator • ICON DV-IDV Series • 4042-575 • Rev. S • 5/11 3