Precoded VCR/PVR Buttons | Hitachi 55HDX61A specification

HOW TO USE THE REMOTE

TO CONTROL VCR/PVR FUNCTIONS

Operating the precoded function for your VCR/PVR (Personal Video Recorder).

This remote is designed to operate different types of VCRs/PVRs. You must first program the remote to match the remote system of your VCR/PVR (refer to pages 51-52 for pre-codes).

1.Turn ON your VCR/PVR.

2.Aim the remote control at the front of your VCR/PVR.

3. To switch to VCR/PVR pre-coded mode, use the SOURCE ACCESS buttons ( , ) on the remote control to position the LED light to the corresponding selection.

4.Hold down the ENT button on the remote and enter the four digit preset code that matches your VCR/PVR, as shown on pages 51- 52. Release the ENT button. The indicator light will flash 3 times if the code was accepted.

5.Aim the remote at the VCR/PVR and press the POWER button. The remote will turn off your PVR when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your VCR/PVR. If the VCR/PVR does not turn off, try a different four digit preset code.

6.The remote will now control your VCR/PVR.

NOTES:

1.If your PVR cannot be operated after performing the above procedures, your PVR’s code has not been precoded into the remote.

2.In the unlikely event that your PVR cannot be operated after performing the above procedures, please consult your PVR operating guide.

3.The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above.

4.VCR precode library is included in the PVR mode. Default device for this mode is Hitachi VCR.

5.INFO, GUIDE and LC (Last Channel) buttons are for PVR devices, not for VCR.

PRECODED VCR/PVR Buttons

These buttons transmit the chosen precoded VCR/PVR codes.

EXCLUSIVE TV Buttons

These buttons are for operating the TV.

A/V NET

GUIDE

THE REMOTE CONTROL

MY VCR/PVR CODE IS:

NOTE: Refer to instruction manual of the VCR/PVR for operation of the buttons exclusively for the VCR/PVR.

47

Image 47

Hitachi 55HDX61A important safety instructions HOW to USE the Remote To Control VCR/PVR Functions, Precoded VCR/PVR Buttons

Contents

Operating Guide for 55HDX61A Do not Open Important Safety Instructions Public Viewing of Copyrighted Material Read before operating equipmentPrevention of Screen Burn First AccessoriesUSE Time Antenna HOW to Setup Your NEW Hitachi Plasma TelevisionFirst Time USE Securing to a wall Vertical Viewing HOW to SET UP Your NEW Hitachi Plasma TelevisionViewing Best Hookup Cables First Time Antenna Connections to Rear Panel JacksUSE Photo Input Front Panel Controls Phones Jack Monitor OUT Rear Panel Jacks RGB Audio Input Upgrade CardTo Power Swivel Connector RGB Analog Input Rear Panel of AVC CableCARD Slot Connecting External Video Sources Connecting Plasma Display Monitor to AVC BOX Before Operating External Video Source Connecting a Monaural Audio Source to INPUT1~INPUT5 Connecting a Stereo VCR or Stereo Laserdisc Player Connecting S-VIDEO VCR or Laserdisc Player DVI to Hdmi Input Hdmi input See page 27 for tips on Rear Panel Connections Digital VCR D-VHS Connecting External Audio Amplifier Connecting External AUDIO/VIDEO Devices Connecting AV Network Setup Procedure Using AV Network Device Codes AV Network Setup Wizard Speakers to on or OFF, then press Select to set Remote controlUse the Cursor Pads To choose AV Receiver To select Internal Speakers AUDIO/VIDEO Codes for AV Network not for remote control Time USE Rear Panel Connections Tips on Rear Panel Connections Remote Control Remote Control HOW to USE the Remote To Control Your Plasma TV 480P Input RGB Analog Input Aspect Display ModeAspect button Ratio Guide button DAY/NIGHT buttonPICTURE-IN-PICTURE button Menu button AV NET button ControlRemote AV NET Learning Wizard Select OK Softkeys. If the device responds, then it is properly set up Ieee Inputs buttonPhoto Input Ant B Ant a Select this menu item to view the chosen picture number Jump Rotate Slideshow When an IEEE1394 device is connected Video When an S-VIDEOInfo button Last Channel LC button Volume VOL WHEEL, Mute buttonChannel CH WHEEL/CHANNEL Selector buttons Dash button PIP button POP Mode PICTURE-IN-PICTUREPress the Cursor PAD or to enable the sub-picture sound PICTURE-IN-PICTURE PIP Ntsc PIP Mode PICTURE-IN-PICTURESplit Mode PICTURE-IN-PICTURE Surf Mode PICTURE-IN-PICTURE Strobe Freeze Main FreezeSplit Freeze Exclusive TV buttons HOW to USE the Remote To Control Cable BOX FunctionsOperating the precoded function for your cable box Precoded Cable BOX buttons PRE-CODED SET-TOP-BOX/SATELLITE Receiver buttons These buttons transmit the chosen precoded DVD codes HOW to USE the Remote To Control DVD FunctionsOperating the precoded function for your DVD player Precoded DVD Buttons These buttons transmit the chosen precoded VCR/PVR codes HOW to USE the Remote To Control VCR/PVR FunctionsPrecoded VCR/PVR Buttons Precoded Audio Buttons HOW to USE the Remote To Control Additional Audio EquipmentOperating the precoded function for your Audio component Input Access Remote VCR Brand Audio Brand ON-SCREEN Display OSD On-Screen Display For Video Audio Channel Manager Locks Timers Setup Power Swivel Display Picture ModeVideo Contrast Noise Reduction Reset Video Settings White Balance ON-SCREENColor Management Color Decoding Audio DRC Language Digital Output Vertical Position AspectAspect Auto Aspect Press Cursor PAD To highlight Ant a or Ant B Channel ManagerSet The Antenna Auto Channel Scan Channel List Signal Meter Locks Movie Ratings TV Ratings Canadian Ratings English Table Canadian Ratings Eng Programming restricted to adults Contains Canadian Ratings FrnCanadian Ratings French Table Programming is not suitable for children Set The Clock Timers Set Day/Night Timer Set Sleep Timer Please Set Clock First Set Event Timer Set Timer Recording Menu Preference Setup Screen Saver Image PowerMenu Background Press Cursor PAD or Screen DisplaySet The Inputs Set Black Side Panel Channel Set Closed Caption Set AV Control This feature will select the source of the Monitor OutputSet Monitor Out CableCARD Info Power Swivel UpgradesSet Stand-By Mode RGB on Screen Display Using the RGB Input Operation No SYNC. Signal Invalid Scan Freq Aspect Setup Power Swivel Move SEL Sel Video Aspect Setup Power Swivel Brightness Color TemperatureInput Contrast Aspect ResetEnhancer Position Using the RGBAuto Adjust Horizontal Clock Clock PhasePhase to factory preset, for current RGB format RGB Input Using Do not Care of Your Hitachi Plasma Display Your Remote Control Ignition Noise Reception Problems Control Useful Info Symptoms Picture Image Spectrum Useful Info Trademark Acknowledgment Plug and Play Agency Regulatory Information Outputs Inputs Hitachi Way Chula Vista, CA Home Electronics Division Digital Media Division 22-25 AccessoriesIndex TruBass Or the Software END User License Agreement for Hitachi DTV Software 102 103 QR64291