Hitachi 55HDX61A AV Network Setup Wizard, Setup Procedure Using AV Network Device Codes

AV NETWORK SETUP WIZARD

SETUP PROCEDURE USING AV NETWORK DEVICE CODES:

A DVD Setup example is shown below. Setup of DVD2, VCR, VCR2, PV Recorder, Cable Box and Set-Top-Box follows this same procedure. If your device is not listed or the device codes not work after following the setup procedure, please refer to the AV NET Learning wizard procedure on pages 33-34.

1.Press the A/V Net button on the remote control.

DVD			POWER	MENU	HOME
DVD2
VCR
VCR2
AV Receiver
Move	SEL	Select

10.If “OK” was selected, and the 4 digit code was invalid, the screen below appears, then goes back to the Device

Code	entry screen.
	ATTENTION
	Find your DVD
	4-digit manufacturers code
	and enter it here

FIRST TIME USE

2. Use CURSOR PADS or to highlight Device Setup.

3. Press the SELECT button or CURSOR PAD on the remote control and the device selection screen appears.

PV Recorder

Cable Box

Set Top Box

Custom

Device Setup

Move SEL Select

4. Use the CURSOR PADS or to choose DVD and press the SELECT button on the remote control.

5.The Setup button on the bottom of the screen becomes highlighted. Press the SELECT button on the remote control to enter the setup screen.

HITACHI AV NET SET UP

Please choose the device to set up.

	( ) DVD			( ) Set Top Box
	( ) DVD2			( ) DVD3 (Custom)
	( ) VCR			( ) VCR3 (Custom)
	( ) VCR2			( ) PVR2 (Custom)
	( ) AV Receiver			( ) CBL2 (Custom)
	( ) PV Recorder			( ) STB2 (Custom)
	( ) Cable Box			List
	BACK		SETUP		MODIFY
Move	SEL	Select

6.Using the remote, enter the four digit Device Code for your equipment, found on page 25.

7. Use the CURSOR PAD	to select Video Input. Press the
CURSOR PADS or	to set the INPUT to which your
device is connected.

8.Repeat step 7 for Audio Input. If the DVD is connected to the TV, select “Using TV”. If the DVD is connected to an external

amplifier, select “no connection”.

9. Press CURSOR PAD			to select Transmission Test. Press
the CURSOR PADS			or	to select Power, Play, or CH UP
softkeys, before pressing the SELECT button to perform a
Transmission Test of the softkey selected. If the device
responds, then it is properly set up. Select OK. (If the
Transmission Test failed, try another code).
	HITACHI AV NET SET UP
	DVD
	Device Code		- - - -
	(Enter Code “9999” to uninstall)
	Video Input		No Connection
	Audio Input		No Connection
	Transmission Test		POWER		PLAY	CH UP
		BACK	OK		EXIT

Move 0-9Input

11.Repeat Device Setup procedure until the screen below appears.

12.Select CONTINUE to setup another device.

HITACHI AV NET SET UP

Congratulations!

Your DVD is now connected to your AV network.

Would you like to set up another device?

Done Continue

Move SEL Select

13.Select DONE to finish and the screen below appears to show the device(s) which has been set-up.

HITACHI AV NET SET UP

	Device		Code	Video	Audio
	DVD		0490	INPUT 2	Using TV
	DVD2		----	Not Setup	Not Setup
	VCR		----	Not Setup	Not Setup
	VCR2		----	Not Setup	Not Setup
	AVR		----	Not Setup	Not Setup
	PVR		----	Not Setup	Not Setup
	CBL		----	Not Setup	Not Setup
	STB		----	Not Setup	Not Setup
	Custom		----	Not Setup	Not Setup
EXIT		SEL	Select

14. Select EXIT to quit.

23