HOW TO USE THE REMOTE TO CONTROL YOUR TV

CD, AMP buttons

When pressed, each of these buttons will blink to indicate the remote is in Audio mode (see page 39).

CHANNEL selector buttons

CHANNEL selector buttons are used to select channels, lock access code, etc.

Enter one, two, or three numbers to select channels. Enter “0” first for channels 1 to 9, or simply press the single digit channel you wish to tune then wait a few seconds for the TV to tune. For channels 100 and above, press the “1” button, wait until two dashes appear next to the channel display on your TV, then enter the remaining two numbers using the number buttons.

Channel selection may also be performed by pressing CH up ( ) or down ( ).

When in ANT C, digital channels are indicated by the use of a (-) DASH in the subchannel number (for example “15-1”). Press buttons [0], [1], [5], [1] to tune to subchannel 15-1 or buttons [0], [1], [5], [0], [0], [1].

NOTE: The TV may not receive some channels if you are not in the correct ANTENNA/CABLE mode (see page 51).

SLEEP and (-) DASH button

Press this button to display the sleep timer in the lower left corner of the screen. Every subsequent press of this button will add 15 minutes to this timer, up to a maximum of three hours. Once set, use INFO when you want to view time remaining. If the SLEEP button is pressed while the timer is set, it will reset to the original condition.

When in ANT C, Digital channels are indicated by the use of a (-) DASH in the subchannel number (for example “15-1”). Press buttons [1], [5], [-], [1] to tune to subchannel 15-1.

INFO button

Press this button when you want to check the channel being received, the picture source, if the channel has stereo (ST) or second audio program (SAP), the time, CHANNEL ID and if the TIMER is set.

 

 

 

 

 

 

3:32 PM

When an S-VIDEO

 

 

 

ANT A/ANT B

 

 

S-IN: 3

Input is connected to

 

 

 

 

 

 

VID 3

VIDEO: 3.

 

 

 

 

3:32 PM

Time

 

 

 

 

 

 

 

 

 

 

 

Ant A 22

Main Picture Source

 

 

 

 

 

 

Stereo

Audio Broadcast

 

 

 

 

 

 

R

Broadcast Rating

 

 

 

 

 

 

1080i Format

Signal Format

 

 

 

 

 

 

 

Wide

 

 

 

 

 

 

 

Mode

 

 

Day/Night

 

 

 

 

3:32 PM

When a

Day

4:3 Expanded

HD 1080i

 

YPBPR: 1

COMPONENT

Closed

Mode

 

Captioning

 

CC Off

View 0:00 AM

Zzzz-:--

Sleep Timer

VID: 1

VIDEO: Y-PBPRInput

 

 

 

 

 

 

 

is connected to

 

 

 

Off Timer

Virtual HD

 

 

VIDEO: 1.

THE REMOTE CONTROL

ANT C

Main Picture

Source

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TV Time

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9:14AM

 

Program Name

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Barney & Friends

Ant C

15-2

 

 

 

 

 

Channel ID

and Information

 

 

 

 

Who’s Who at the Zoo

 

 

 

KPBS-DT

 

 

 

 

 

 

 

 

Barney and the chi... 4:00PM

5:00PM

 

Program Time

 

 

 

 

 

 

 

 

 

480i

 

Engl

 

TV-Y

 

 

CC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Digital Closed Caption

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Broadcast Rating

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Program Language

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Digital Input Signal

Day/Night

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Closed Mode

 

 

 

Day

 

 

 

4:3 Expanded

 

HD

1080i

 

 

 

 

 

 

 

 

Captioning

 

 

 

CC Off

 

 

 

0:00 AM

 

 

 

 

 

 

 

-:--

 

Sleep Timer

 

 

 

 

 

 

 

View

 

 

 

 

 

 

Zzzz

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Wide Mode

Off Timer

Virtual HD

 

IEEE1394

When an IEEE1394 device

is connected

 

 

 

9:14AM

 

No Information

IEEE1394

 

01/04

Multi

 

 

 

PBS 1 DT

Channel

 

-:--AM

-:--AM

 

Programs

 

Multi

CC

 

 

NOTES: 1. When an IEEE1394 device is connected, press CH , CH buttons to change Multi Channel programs.

2.When in ANT C or a 1394 device, press the INFO button twice (2x) to see detailed program information when available.

23

Page 23
Image 23
Hitachi 51S700, 57S700, 65S700 CD, AMP buttons, Channel selector buttons, Sleep and Dash button, Info button