Installation Guide (continued)
安裝指南（續）
How to Install the Water Supply Hose
供水管的安裝
Connecting the water supply hose to the washer 供水管與機體的連接
Firmly tighten the union nut | Union nut |
when connecting the water |
|
supply hose to the water inlet. |
|
沿箭頭方向旋轉連接螺母，使其 |
|
與供水口緊緊相連。 |
|
•Loosely tightened union nut will cause water leakage.
請務必擰緊供水管與機體的連接螺母。否則，將會漏水。
•When removing the hose, unscrew the union nut fi rst.
拆卸供水管時，先鬆開連接螺母，再進行拆卸。
Extending the water supply hose 供水管的延長
Please use optional extension pipe to extend length of the water supply hose.
請使用另行銷售的延長供水管。
•Three standard extension hoses (1m,2m,3m) are available. Please inquire distributors for
extending the water supply hose.
備有1m 、2m和3m三種規格供購買。如欲延長供 水管，請向銷售商查詢。
How to Install the One Touch Joint
便捷連接器的安裝
1 | Confirm the diameter of the water tap. | ||
確認水龍頭直徑。 | Screw | ||
• If the diameter exceeds | |||
|
| ||
| 2cm, remove the joint | Joint ring | |
| ring. | ||
|
| ||
| 若水龍頭的外經超過 | Label | |
| 2cm，可將連接環取出。 | ||
| One touch joint | ||
2 Check the distance between joints A and A.
確認接頭A、B之間的間隙。
• Screw joint B in the | Joint A | |
arrow direction to adjust | A | |
Approximately 6mm | ||
the gap. | ||
6mm | ||
沿箭頭方向旋轉接頭B調 | Joint B | |
| B |
整間隙。
3 | Press the sealed | Water tap |
|
pad evenly
4 Tighten joint B in the arrow direction
Joint A
A
against the tap and tighten the four screws uniformly.
將密封墊均勻地壓 在水龍頭上，再將 4個螺釘均等地擰 緊。
Sealed pad |
Joint B |
B |
Tighten screw in advance if it is located close to the wall.
to reduce the gap between joint A and
B to 4mm or less. 沿箭頭方向擰緊接頭 B ，使接頭A 、 B 之間的間隙在4mm以 內。
Joint B
B
(After tighten)
( )
Less than 4mm 4mm
•For water supply hose installation, please refer to "How to install the water supply hose" in the user manual.
供水管的安裝參閱使用說明書中「供水管的安裝」一章。
•Loosening may occur after a long time use. In such a case, reinstall the joint following steps 2 to 4.
長時間使用後，可能會因鬆脫而引起漏水，此時請按2~4的步驟重新安裝。
(Follow the same steps when reinstalling the one touch joint when you move the machine to another location.) （搬家等需重新安裝便捷連接器時，請按照相同的步驟進行。）
Appropriate water tap | Horizontal taps A and B as shown below. |
|
|
| ||||||||||||||||
適用的水龍頭 |
|
|
|
|
|
|
|
| 橫式A、B型水龍頭最為適宜。 | Swivel tap | ||||||||||
Horizontal tap A | Horizontal tapB | Square mouth tap | Universal household tap | |||||||||||||||||
萬能水龍頭 | 萬向水龍頭 | |||||||||||||||||||
橫式A型水龍頭 | 橫式B型水龍頭 | 方口水龍頭 | ||||||||||||||||||
|
|
|
| |||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Distance must be over 1.6cm
May break off after installing
in order to install correctly. 1.6cm
the one touch joint.
Water leakage may occur.
10
2013/10/15 15:11:49
