Installation Guide
安裝指南
Installation of Washing Machine 洗衣機的安裝
Where to install 安裝地方
Please install on a solid horizontal surface.
請安放在堅硬、平坦的地面上。
•Installation on a slippy or irregular surface may result in noise and shaking.
安放在易於滑動、柔軟的地面上，會容易產生振動和噪音。
Avoid installing the unit too close to the wall.
請勿靠近牆壁安放。
• This is to prevent abnormal vibration and noise.
以防止異常振動和噪音。 | At least 1.5cm |
| 1.5cm |
How to install 安裝方法
Solid, horizontal surface | Weak surface | Irregular surface | |
堅硬、平坦的地面 |
| 柔軟的地面 | 凹凸的地面 |
At least 1.5cm |
|
|
|
1.5cm |
|
|
|
At least 9cm(Water drainage hose onside) |
| ||
9cm ( | ) |
|
|
The unit should be installed on a flat horizontal surface.
請水平安裝洗衣機。
Otherwise sudden stop or abnormal sound may occur during the spinning cycle.
若安裝得不水平，會導致脫水時停機或產生異常聲音。
Put the washing machine at the installa- |
| According to the bubble location on the | |||||||
1 tion place. |
| horizontal indicator, rotate the adjust- | |||||||
3 able leg to locate the bubble at the | |||||||||
• Make adjustment according to the following steps if |
| circle center. | |||||||
|
|
|
|
|
|
|
|
| |
the washing machine is not put on a flat horizontal |
|
|
|
|
|
|
|
|
|
surface or there's gap under the leg: |
|
|
|
|
|
|
|
|
|
|
| If the bubble is out of half of the | |||||||
• Heighten the adjustable leg till no gap exists at its side. |
| circle radius, the ground is too |
|
|
| ||||
|
|
| |||||||
| sloppy to be regulated to flat with |
| |||||||
|
| only the adjustable leg.The plank |
|
|
|
| |||
|
|
| |||||||
• If there's gap opposite to the adjustable leg, make the rear | shall be properly inserted. |
| |||||||
leg stand closely on the ground, and insert proper plank |
| plank |
|
|
|
|
| ||
between the front leg and the ground to fill up the gap. |
|
| |||||||
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2 Check the bubble location on the horizon- tal indicator.
•No leg adjustment is required if the bubble is right at the circle center.
4 Check the existence of gap under the washing machine leg.
•If gap exists, adjust the adjustable leg.
Circle
Bubble
Observe the horizontal indicator from above.
Loosening |
| Tightening |
| Lock nut |
|
| Adjustable leg | Lock nut |
|
| |
Elevating | Lowering |
|
•Adjust height with the adjustable leg if the bubble is not in the circle.
5 Remove the horizontal indicator. Close the lid.
Installation of the bottom plate 底板的安裝
The bottom plate is placed on the packaging foam on the top of the washing machine. 出廠時，底板安放在洗衣機頂部的包裝發泡上。
1 | Please lay down the | Align the hook on the bottom plate with the |
washer slowly. | square hole on the chassis and insert it, and | |
請將機體輕輕地放倒。 2 then tighten the screw. | ||
將底板上的倒鉤對準底盤上的方孔插入，然後擰緊螺釘。
8
2013/10/15 15:11:48
