TROUBLESHOOTING

Symptoms That Seemingly Appear to be Failures

Make the checks suggested below depending on the symptoms observed. If the symptoms remain uncorrected, contact your dealer.

WARNING

• Customer servicing can be hazardous.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Symptom

 

 

 

 

 

 

 

Point to check

See

 

 

 

 

 

 

 

page

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• No picture with the power-

 

 

 

 

 

 

 

• Check the way the power cable is connected.

6

 

 

 

 

 

 

 

indicating lamp off.

 

 

 

 

 

 

 

• Press the power switch.

7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• The message “POWER

 

 

 

 

 

 

 

No sync signal is detected.

6

 

 

 

 

 

 

 

SAVE” is displayed.

 

 

 

 

 

 

 

• Check the way the signal cable is connected.

 

 

 

 

 

 

 

 

 

 

POWER SAVE

 

• Make sure that the switch of the computer,

7

• No picture with the power

 

 

 

 

 

 

 

imaging equipment , etc., is turned on.

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Make sure the computer is not in the power-save

indicating lamp flickering in

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

mode.

10

green.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Check to see if the input selection matches the

21

 

 

 

 

 

 

 

 

connection terminal.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

28

 

 

 

 

 

 

 

 

 

 

• The message “OUT OF

 

 

 

 

 

 

 

An input signal is not received normally.

6

 

 

 

 

 

 

 

FREQUENCY” is displayed.

 

 

 

 

 

 

 

• Check to see if the input signal matches the

7

 

 

OUT OF FRQUENCY

 

monitor specifications.

 

 

 

• Check the way the signal cable is connected.

21

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• The power indicating lamp is

 

 

 

 

 

 

 

• Check the contrast and brightness settings

6

 

 

 

 

 

 

 

normally lit but no picture .

 

 

 

 

 

 

 

(adjust them for higher contrast and brightness).

7

 

 

 

 

 

 

 

 

• Check the way the signal cable is connected.

 

 

 

 

 

 

 

 

 

11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

13

 

 

 

 

 

 

 

 

 

 

• The display image appears

 

 

 

 

 

 

 

• Adjust the dot clock frequency and phase.

15

 

 

 

 

 

 

 

flowing slantwise.

 

 

 

 

 

 

 

(Adjust the dot clock frequency first, the dot clock

16

• Text displayed across the

 

 

 

 

 

 

 

phase next.)

 

 

 

 

 

 

 

 

screen appears vertically

 

 

 

 

 

 

 

(RGB input)

25

 

 

 

 

 

 

 

streaked, with the characters

 

 

 

 

 

 

 

 

 

in vertical columns blurred.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Text displayed across the

 

 

 

 

 

 

 

• Adjust the dot clock phase for the clearest

15

screen appears blurred.

 

 

 

 

 

 

 

viewing.

16

• A fine pattern flickers when

 

 

 

 

 

 

 

(RGB input)

displayed on the screen.

 

 

 

 

 

 

 

 

26

 

 

 

 

• The remote controller does not work.

 

• Check to see if the batteries are loaded in the

8

 

 

 

 

 

 

 

 

remote controller in opposite direction.

 

 

 

 

 

 

 

 

 

Check to see if the batteries in the remote controller are OK.

ENGLISH

23

Page 39
Image 39
Hitachi CMP4121HDU Troubleshooting, Symptoms That Seemingly Appear to be Failures, Customer servicing can be hazardous