Executing Phantom Buttons, Enter Scene | Home Automation OmniPro II

Executing Phantom Buttons

OmniPro II can turn on and turn off each of the 17 possible Phantom Buttons. Phantom Buttons must be pre-programmed into the RS-232 interface or Chronos. Phantom Button 16 is always assigned to “All On” (if the Phantom button is turned on or off) and Phantom Button 17 is always assigned to “All Off” (if the Phantom button is turned on or off).

To issue Phantom Button commands, from the top-level display or from the main menu, press the 4 (ALL) key on the console keypad, and then press the 4 (PHANTOM) key. You are prompted to enter a Phantom Button (1-17).

ENTER BUTTON: 1-17

Enter the Phantom Button number (1-17) followed be the ' # ' key.

PHANTOM BUTTON 1 0=OFF 1=ON

When a Phantom Button is turned on, all of the devices that are pre-programmed with that Phantom Button will go to their preset light levels. When a Phantom Button is turned off, all of the devices that are pre-programmed with that Phantom button will turn off.

Executing CentraLite Scenes

OmniPro II can turn on and turn off each of the 255 possible CentraLite Scenes. To issue CentraLite Scenes commands, from the top level display or from the main menu, press the 4 (ALL) key on the console keypad, and then press the 5 (CENLIT) key. You are prompted to enter a Scene (1-255).

ENTER SCENE: 1-255

Enter the CentraLite Scene number (1-255) followed be the ' # ' key.

CENLIT SCENE 1 0=OFF 1=ON

When a CentraLite Scene is turned on, all of the devices that are pre-programmed for that scene will go to their preset light levels. When a CentraLite Scene is turned off, all of the devices that are pre-programmed for that scene will turn off.

Page 29

Image 37

Home Automation OmniPro II Executing Phantom Buttons, Executing CentraLite Scenes, Enter Button, Enter Scene, Page

Contents

Control & Security System HOME AUTOMATION, INCDocument Number 20R00-2Rev. January All Rights Reserved Copyright 2001-2006Home Automation, Inc OVERALL DESCRIPTION INTRODUCTIONSECURITY SYSTEM OPERATION Contents CONTROL TELEPHONE CONTROL SETUP FEDERAL COMMUNICATION COMMISSION NOTICE UNDERWRITERS LABORATORIES REQUIREMENTSCANADIAN INDUSTRY CANADA NOTICE APPENDIX A - DIAL OUT PLANNERPage Underwriters Laboratories UL Listing INTRODUCTIONPage Console Operation OVERALL DESCRIPTION1- OFF 2- DAY Display Menus Normal Top-LevelDisplay6- UP ARROW 7- CONSOLE LED Main Menu Error BeepsTrouble Beeps To silence the beeper, press the * key Cancel OmniPro II MaintenanceAreas Confirmation Beep Arming the Security System SECURITY SYSTEM OPERATION0 = OFF 1 = DAY 2 = NIGHT Using Shortcut Keys3 = AWAY 4 = VACATION Quick Arm 9 = RESTOREBypassing Zones Restoring Zones What Happens When the Alarm is Activated What To Do When You Come HomeBurglar Alarm Activated #=GOTO Gas Alarm Activated Fire Alarm ActivatedEmergency Keys Page Alarm Reset Duress Code Entered or Duress Alarm ActivatedAlarm Cancel Police Emergency Codes Trouble IndicationsMaster Code Page Duress Code Panic SwitchesArea Arming Manager Code Page GOTO Area Page Testing Your System CONTROL Control CommandsAbout UPB Page Room Controller LED Indicators When set to UPB, the OmniPro II controller canHAI Lighting Control HLC Format About Rooms About Lutron RadioRA About CentraLiteAbout House Controllers Page About About ALCHouse Codes ALC Module Types OmniPro II Unit Numbers Unit NumbersModule / Output Unit Numbers Page Scrolling Through Names Configuring Lighting Scenes in an HLC RoomControlling Units Controlling a Room of HLC Lighting Operation StepControlling CentraLite Units Page Controlling ALC or X-10Units Controlling RadioRA UnitsPage Scene Command Compose Ramp Command ALCControlling Compose Units Page Status of a Unit Timed CommandsInternal Flags Page All On / Off Controlling OutputsAll Lights On All Off Scene Set Command Scene CommandsScene On Command Leviton Scene Control Setting a Link Lighting Scenes Scene Off CommandUPB Links Activating and Deactivating Links Executing CentraLite Scenes Executing Phantom ButtonsENTER BUTTON PHANTOM BUTTON 1 0=OFF 1=ON Temperature Control ButtonsLeave for Work Button Dinner for Two Button Page HAI RC-SeriesThermostats Page Programmable Energy Saver Modules PESMs Page The following control actions are allowed on PESMs IMPORTANT NOTES Freeze AlarmsIndoor and Outdoor Temperature Page Humidity Temperature AlarmsOutdoor Temperature Temperature Control of Appliances Configuring HLC Devices using an Omni Console Configuring HLC DevicesStatus Page Step Operation Setup Mode for HLC DevicesStep Operation Step Operation OFFHK - OFF HOOK ONHK - ON HOOKRING - RINGING DEAD - DEAD PHONE LINE Page THROUGH Show Events Event LogPage Record Memo Message MessagesPlay Memo Message Clear Text Messages Log Message Show MessageClear Message Say Message SERIAL PORT Send Message Pro-LinkMSGNAME ENTER MESSAGE Telephone Interface TELEPHONE CONTROLIn-HousePhones Remote Phones Alternate Method Phone Access Denied - Remote LockoutMain Menu Page 2 - Security 1 - Control3 - Button 4 - All When a Programmable Energy Saver PESM is entered When an HAI Communicating Thermostat is entered6 - Status 7 - Events 8 - Message When the HAI Two-WayAudio Module is being usedPlaying and Recording a Message Paging and Listening Panic Button over the Phone # # # # # # 9 - Good-ByePlaying and Recording the Address Page Digital Dialer Emergency Dial-OutVoice Dialer How the OmniPro II Voice Dialer Works What You Hear - If Your OmniPro II Calls You PC AccessEntering the Code Page Built-InEthernet Port Connecting to Network via PC AccessOmniPro II Ethernet Connections Page Dynamic DNS Local NetworkPage i.e Local / Wide Area Networki.e Page Set Up Codes SETUPAccess Areas Authority Level Duress Code Set Up TimeTIME Page 1 = Add Programs Advanced Control Programming ACP2 = Show Programs Page Page Menu 3 = Delete All Programs Edit ProgramsPage Times Programs Edit Programs WhenPage Button and Event Programs Control Unit / Switch Press Event ButtonsPage Switch Corresponding Switch TableOmniPro UPB 6-ButtonKeypad All On/Off Event Buttons Zone Event ButtonsUPB Link Event Buttons Page X-10Event Buttons Alarm Event ButtonsMiscellaneous Event Buttons Page Message Event Buttons Pro-Link Switch Press Event Buttons CentraLitePage Program Control Commands Edit Program CommandPage Program Security Commands Unit Toggle CommandProgram Button Commands Program All On / All Off Commands Program Message Commands Program Video CommandsProgram Temperature Commands Program Energy Cost Program Control Conditions Edit Program ConditionProgram Security Mode Conditions Program Zone Conditions Program Other Conditions Program Time Clock ConditionsPage Telephone Access Set Up DialRemote Commands Answer Outside Call Dial Out Numbers Dial Out NumberDial Order Page Entry Delay Set Up ArmingExit Delay Audible Exit Delay Enable Quick Arm Set up MiscellaneousEnable Auto Bypass All On For Alarm Flash For Alarm Enable Freeze AlarmHouse Codes 1-16Format FORMAT Time Clocks House Codes 1-16All OnPage ZONE NAME Latitude, Longitude, and Time ZoneDaylight Savings Page Controller Port Number Controller IP AddressNUMBER DESCRIPTION Encryption Key Set Up NamesPage Set Up Address Set Up VoiceSET UP VOICE 1=CTRL 2=ZONE 3=BTTN ↓ 4=CODE 5=TEMP 6=AREA 8=MSG↑ FIRE ESCAPE PLANNING UNDERWRITERS LABORATORIES REQUIREMENTSPage Page FEDERAL COMMUNICATION COMMISSION NOTICE IF YOU HAVE TROUBLE WITH YOUR PHONES CANADIAN INDUSTRY CANADA NOTICEPage OmniPro II Voice Dial-OutPlanner APPENDIX A - DIAL OUT PLANNERPage Page INSTRUCTIONS TO CALLED PARTY CODE CHAR APPENDIX B - TEXT DESCRIPTION CHARACTER CODESCODE CHAR CODE CHAR CODE APPENDIX C - VOICE DESCRIPTION CODESDESCRIPTION CODE DESCRIPTION CODECODE DESCRIPTION DESCRIPTION CODECODE DESCRIPTION CODE NOTES ON CUSTOM PHRASESDESCRIPTION CODEPage HAI New Orleans, LA U S A NOTE TO INSTALLER