Manuals / Homelite / Lawn and Garden / Chainsaw

Homelite CSP3816 Features, Trigger Release Silencer Chain Oil Cap, Front Hand Guard Chain Brake

Models: CSP4518 CSP3816

1 40

Download 40 pages 3.06 Kb

Page 10

Image 10

FEATURES

TRIGGER

RELEASE

SILENCER

CHAIN OIL CAP

FRONT HAND GUARD/

CHAIN BRAKE

FRONT

HANDLE

CYLINDER

COVER

CHAIN

CATCHER

CHOKE LEVER

PRIMER BULB

STARTER GRIP

STARTER/FAN HOUSING

ON/OFF SWITCH

FUEL MIX CAP

SAFE-T-TIP®

CARBURETTOR

ADJUSTMENT

REAR

HANDLE

THROTTLE
TRIGGER	Fig. 2
	Fig. 2

UK - Page 10

Page 10

Image 10

Homelite CSP3816 manual Features, Trigger Release Silencer Chain Oil Cap, Front Hand Guard Chain Brake, UK - Page, Throttle

Contents

CSP3816 - 406 mm 16 in. 38cc Chainsaw OPERATOR’S MANUALSAVE THIS MANUAL FOR FUTURE REFERENCE CSP4518 - 457 mm 18 in. 45cc ChainsawINTRODUCTION TABLE OF CONTENTSUK - Page READ ALL INSTRUCTIONS GENERAL SAFETY RULESUK - Page KEEP ALL PARTS OF YOUR BODY away from the saw GENERAL SAFETY RULESUK - Page SAFETY APPAREL SPECIFIC SAFETY RULESGENERAL PRECAUTIONS BASIC PRECAUTIONS IN THE CUTTING/ WORK AREAKICK-BACK MAINTENANCE PRECAUTIONSPUSH AND PULL PULL PUSHNAME SYMBOLSSYMBOL EXPLANATIONPetrol SAVE THESE INSTRUCTIONSSYMBOLS with an octane rating of 87 R + M / 2 or higherSPECIFICATIONS UK - PageSAFE-T-TIP CARBURETTOR ADJUSTMENT REAR HANDLE FEATURESSTARTER/FAN HOUSING ON/OFF SWITCH FUEL MIX CAP TRIGGER RELEASE SILENCER CHAIN OIL CAPOPERATION UNDERSTANDING YOUR CHAINSAW SAFETY DEVICESWEAR “NON-SLIP”OR CHAPS GLOVES WEAR STURDY BOOTS SAFE-T-TIP ANTI-KICK-BACKNOSE GUARDRUN POSITION BRAKE POSITION KICK-BACKPRECAUTIONSCHAIN BRAKE KICK-BACKDANGER ZONEMIXING THE FUEL FUEL AND REFUELLINGHANDLING THE FUEL SAFELY FILLING THE TANKSTARTING THE ENGINE IGNITION SWITCH IN THE RUN POSITIONADDING OIL BRAKE POSITIONSTARTER GRIP STARTING A COLD ENGINECHOKE LEVER CHOKESTARTING A WARM ENGINE IGNITION SWITCH IN THE STOP POSITIONSTOPPING THE ENGINE OPERATIONPROPER CUTTING STANCE PREPARING FOR CUTTINGPROPER GRIP ON HANDLES CHAIN LINEADJUSTING THE CARBURETTOR BASIC OPERATING/CUTTING PROCEDURESWORK AREA PRECAUTIONS AIR FILTERRUN POSITION ADJUSTING IDLING SPEEDOPERATING THE CHAIN BRAKE OPERATIONSee Figure WEIGHT OF HEAVY LIMBSC DEAD LIMBS CLEARFELLING TREES HAZARDOUS CONDITIONS STAY AWAY FROM ELECTRICAL LINES AND BUILDINGSRETREAT PROPER PROCEDURE FOR TREE FELLINGPLANNED LINE OF FALL OPERATIONBACK CUT HINGE 5 cm 2 in. OR 1/10 DIA NOTCH APPROX. 1/3DIAMETER OF TRUNK 5 cm 2 inBUCKING WITH A WEDGE REMOVING BUTTRESS ROOTSBUCKING VERTICAL CUT LOOSE SECTION HORIZONTAL CUTUNDER-BUCKING BUCKING LOGS UNDER STRESSOVER-BUCKING LOG SUPPORTED AT ONE ENDLOAD LIMBING AND PRUNINGCUTTING SPRING POLES SECOND CUTASSEMBLING THE BAR AND CHAIN MAINTENANCEDANGER See Figures 41 throughCHAIN DRIVE LINKS CHAIN DRIVE LINKS BAR STUDS ADJUSTINGPINCUTTERS GUIDE BAR PLATE SPROCKETMAINTENANCE CHAIN TENSIONING SCREWUK - Page APPROXIMATELY 1.25 mm ADJUSTING THE CHAIN TENSIONCHAIN MAINTENANCE FLATS ON DRIVE LINKSINSPECT DRIVE SPROCKET SHARPENING THE CUTTERSRAKER CLEARANCE CUTTINGMAINTENANCE CHECK FOR WEAR OR DAMAGE LEFT-HAND CUTTERSRIGHT-HAND CUTTERS UK - PageSIDE PLATE ANGLE MAINTAINING DEPTH GAUGE CLEARANCETOP PLATE FILING ANGLE CORRECT LESS THAN 30MORE THANMAINTAINING THE SAFE-T-TIP NOSE GUARD RESTORE ORIGINAL SHAPE BY ROUNDING THE FRONTMAINTAINING THE GUIDE BAR LUBRICATING HOLEMOUNTING THE SAFE-T-TIPNOSE GUARD CLEANING THE AIR FILTERFAN HOUSING BAFFLE PRE-FILTER STARTER ASSEMBLY TIGHTEN 3/4 OF A TURNCLEAN FLYWHEEL FINS CLEANING THE STARTER UNITCLEANING THE ENGINE CLEAN CYLINDER FINSCHAIN BRAKE CLEANING THE SPARK ARRESTING SILENCERCLEAN THE CHAIN BRAKE STORING THE CHAINSAW 1 MONTH OR LONGERPROBLEM TROUBLESHOOTINGBAR AND CHAIN COMBINATIONS SOLUTIONEngine starts, runs, and TROUBLESHOOTINGUK - Page GUARANTEE - STATEMENT RTSA / RTUK / RTG WARRANTYUK - Page UT74123B UT74125B OPERATOR’S MANUALRyobi Technologies GmbH Itterpark D-40724Hilden Germany

FEATURES

TRIGGER

FRONT HAND GUARD/

FRONT

CHOKE LEVER

STARTER/FAN HOUSING

SAFE-T-TIP®

THROTTLE

TRIGGER