Hoover SpinScrub manual To clean nozzle, Clean Surge Button

To clean nozzle

If lint or other debris becomes lodged in nozzle, do not attempt to remove nozzle cover.

Pour one to two cups of clear water on a non-carpeted floor. Do not pour water onto a wood floor.

Pick up the water with your deep clean- er. Repeat as necessary until debris is flushed out of nozzle.

3-3

Some models have a nozzle clean-out tool for removing debris or if a non-car- peted floor is not available. To use the tool:

Disconnect deep cleaner from electri- cal outlet.

Slide tool into nozzle and remove debris as shown.

To clean the outside of the machine, wipe off dirt with a cloth dampened in warm water and mild detergent. Do not use solvent or petroleum based prod- ucts to clean the machine .

Carpet Cleaning

Read “Before you begin cleaning” instructions on page 9.

1.Fill clean solution tank (upper tank) with HOOVER Carpet/Upholstery Detergent according to instructions for Figs. 2-9 to 2-15.

2.Move speed selector to LO for gen- tle cleaning or Hl for normal cleaning.

3.Dry hands and plug cord into a prop- erly grounded outlet.

Do not clean over floor electrical out- lets.

4.To avoid walking on damp carpet, start at the end of the room farthest from the door or path to sink where tanks will be emptied and filled.

Step on handle release pedal and lower handle to operating position; turn deep cleaner ON.

5.Squeeze trigger to release cleaning solution and slowly push deep cleaner forward (equals one wet stroke).

6.Continue to squeeze trigger and slowly pull deep cleaner back toward you (second wet stroke). Release trigger and slowly push deep cleaner forward over area just sprayed with solution (dry stroke). Then slowly pull deep cleaner back toward you without squeezing trig- ger (dry stroke). Continue going over the area with dry strokes until the green ‘MAX Extract’ light comes on.

7.Overlap strokes by 1 inch to help pre- vent streaking.

Keep nozzle flat on floor for both forward and reverse strokes.

3-4

8.For heavily soiled areas, repeat steps 5-7. Avoid saturating carpet, as noted below.

9.For particularly soiled carpet or spots, use the Clean Surge™ button (see fol- lowing section). Avoid saturating carpet, as noted below.

Note: To avoid saturating carpet, do not use more than 4 wet strokes over one area. Always end with dry strokes.

It is best to alternate wet and dry strokes as described above.

For best cleaning results and to aid in faster drying of carpet, end with more dry strokes. (Continue using dry strokes until little water is visible passing through the recovery tank lid and the green ‘MAX Extract’ light comes on.)

10.Empty recovery tank when the red ‘MAX Extract’ light comes on and the motor sound becomes higher pitched and there is a loss in suction (see “Automatic shut-off”, Fig. 2-7)

When finished cleaning, follow “After cleaning” instructions on pages 9 & 10.

3-5

Clean Surge™ Button

The ‘Clean Surge’ button can be used to dispense extra solution when cleaning particularly soiled areas of carpet or spots.

To use, press ‘Clean Surge’ button while squeezing solution trigger. For normal solution spray, release button and con- tinue to squeeze solution trigger.

Picking up spills

Your deep cleaner may also be used to pick up small liquid spills (1 gallon or less, never to exceed 1/4 inch in depth) on carpet, upholstery, or bare floors.

1.For best results, pick up spills imme- diately by placing the stair/upholstery nozzle just above the spill and suction up any residue on top of the carpet.

2.If the spill remains, place either the stair/ upholstery nozzle or floor nozzle with brushes turned OFF in front of the spill, pull the nozzle very slowly over the spill initially with suction only.

Repeat with spray and suction.

When picking up spills on bare floors , use only the floor nozzle with the bare floor attachment in place and speed selector in the OFF position (this will help prevent spreading the spill).

If a spot is left, the stair/upholstery nozzle is generally more effective for removing it.

Although no cleaning solution can com- pletely remove all spots, they can be treat- ed by following the instructions provided by the manufacturer of the carpet, uphol- stery, or bare floor surface being cleaned.

Do not use the deep cleaner to pick up f l a m m a ble or combu s t i ble liquids or ch e m i c a l s .

When finished, follow “After cleaning” instructions on pages 9 & 10.

10