Manuals / Brands / Computer Equipment / Switch / HP / Computer Equipment / Switch

HP 12076A LAN/1000 LINK Node Manager Software Services, LANVCP Operation

1 156

Download 156 pages, 564.61 Kb

LANVCP Operation

LAN Virtual Control Panel (LANVCP) server software for downloading systems or controlling •front panel" operations of a remote node is provided with VC+ (HP 92078A). For a given LANIC card, the LANVCP server software and the Node Manager software receive packets through the same •channel", which is governed by the design of the driver and other software. An intermediate program, DISPATCH, is provided to inspect and properly route incoming packets to the appropriate program or software module. DISPATCH must be used when both the Node Manager and other LANVCP software access the same LANIC card.

The server software required for LANVCP operation are the following modules: DISPATCH, RMVCP, VCPMT, IPL_BUILD and IPL_EDIT. These modules are shipped in the /VCPLUS/LANVCP directory. LANVCP operation and these required modules are described in more detail in Chapter 6.

Node Manager Software Services

The Node Manager software provides four primary categories of services: Configuration, Statistics, Diagnostics and Event Logging. Since Node Manager software at one node can •talk to" Node Manager software at another node, these services may be accessed locally or remotely. This is illustrated in Figure 1"3.

End User

Terminal

User Interface

Commands From

Local User Interface

	Commands						Commands
	Commands		Node Management Server				Commands
	From Remote						to Remote
	From Remote						to Remote
	Server						Server

			Access to
			Node Manager Services

Configuration Statistics Diagnostics Event Logging

Figure 1%3. Node Manager Software Services

Introduction 1%5

Contents

HP 12076A LAN/1000 Link Node Manager's Manual NOTICE Printing History Page Preface Purpose Assumptions Related Reading Organization Table of Contents 3"6 3"7 3"8 3"9 Node Manager Operations 5"5 5"6 5"7 Group I: Commands Not Containing the FileAddress Parameter 5"8 5"58 LANVCP Operations 6"1 6"2 6"4 List of Illustrations Tables Page Introduction Identification Installation System Requirements Page Software System Memory LANVCP Operation Node Manager Software Services Configuration Services Statistical Services Diagnostic Services Event Logging Services Implementation Considerations Designating Nodes General Information Open Systems Interconnection Model Note IEEE 802 Service Types Transmission Frames Format Preamble Start Frame Delimiter Destination Address where: CA = Card Address bits comprising the lower six hex digits Globally Administered Address Locally Administered Address Individual node address Source Address Length Protocol Data Unit Page Page Control Page Information Poll bit (for commands) or Final bit (for responses) as previously defined bit values establish the Logical Link Control services provided, Type and/or Type bits are reserved and are set to •0 bits are for Receive Window Size defined for Type 2 services Pad Frame Check Sequence Page Software Installation Installation Summary Modules Provided Answer File Entries Table Generation Example 31. Sample Table Generation Entries for Two LANIC Cards Installed (An asterisk •*" denotes a comment line) sc1, lu1 are Card 1's select code (in Octal), and logical unit number sc2, lu2 Linking Node Manager Software Using LAN8023.CMD Driver and Node Manager Initialization Verifying the System Page Node Manager Operations Node Manager Modules Command Processing Command Entry Errors Command Execution Errors Files and Directories MCAST.TXT Page EL.TXT Driver Interface Driver's Class Table Packet Routing Saving Orphan Packets RAM & NOVRAM Driver's Copy Node Manager Software Initialization Page Finding Link File Directories Entering User Commands Initialization Errors Post Initialization Packet Filter Addressing Modes Page Multiple LANIC Cards Using Node Manager Parameter Notation Getting Started Exiting the Node Manager Software Using the Help Facility NM Using the Command Stack Command Entry Timeout Error Messages Command Execution Node Manager Commands Group I: Commands Not Containing the FileAddress Parameter Group II: Commands Containing the FileAddress Parameter Retrieving the ADR Parameter Configuration Commands Read Link Configuration Command (RC) Multicast Address Considerations Page RC Command Examples Page Page Page Set Link Configuration Command (SC) Page Station Address Considerations Download Server Station Address Considerations File Server Station Address Considerations Packet Filter Mode Considerations SC Command Examples Update Link Configuration Command (UC) Page UC Command Example Insert Multicast Address Command (IM) IM Command Examples Delete Multicast Address Command (DM) DM Command Examples Create Link File Directories Command (CD) CD Command Example Purge Link File Directories Command (PD) PD Command Example CK Command Examples Diagnostic Commands The Rep Parameter 1.Press any key, resulting in the Command Monitor system program prompt (CM>) 2.Set the break flag for the NM module, as follows: LANIC Self%Test Command (TC) The syntax for this command is: This is the •target" Station Address of the node whose LANIC card undergoes TC Command Examples Page Do External Loopback to MAU Command (EL) EL Command Examples Example 2. External Loopback Test Failure Issue TEST Loopback Command (TEST) This is the •target" Station Address of the node to which the TEST command See Table 5"1 for default addresses process, on the ADR node, for which the IEEE 802.2 TEST command packet is directed, and from which an IEEE 802.2 TEST response packet is desired. This DSAP Considerations Self%Addressed TEST Packets Errors TEST Command Examples Example 2. Incorrect MSGLEN Parameter MSGLEN Rep Example 4. Self"Addressed TEST Commands XID Command (XID) process (on the ADR node) for which the IEEE 802.2 XID command packet is directed and from which the XID response packet is desired. This parameter is required and entered as a two"digit hexadecimal number set (see •The Rep Parameter" discussed earlier in this chapter) Self%Addressed XID Packets XID Command Examples Event Log Commands Read Event Log File Command (RE) RE[,FileAddress] where TIME DATE List Facility RE Command Examples Example 3. Bad Packet Entry in Event Log File Example 4. Trace Packet Entry in Event Log File Statistics Commands Page Statistics Description Page Read Link Statistics Counters Command (RS) This is the Logical Unit number of the LANIC card through which the command is local LANIC card. See Table 5"1 for default values RS Command Example ZS Command Example LANVCP Operations Memory%Based System, LAN, and VCP Hardware and Software Requirements IPL_BUILD and IPL_EDIT - Configuration Files Page Examples Format of IPL_TABLE.TXT Selecting the System File to Download DISPATCH - Monitoring LAN Packets VCPMT Monitor RMVCP - Remote VCP /BREAK /EXIT /HELP /READ /WAIT Examples RMVCP Memory Dump Session RMVCP enter number of byte pages of Downloading Over a LAN Link Page Error Codes & Descriptions NMGR Error Codes Driver Error Codes LANVCP Error Codes -14:Unexpected_session received message in error, type: <VCP message type VCPMT initialization was unable to open the error printer file (LU 1) -17:Interactive session received message in error, type: <VCP message type -19:Error in reading download file, FMP error: <FMP error -23:Memory dump failed on LAN address <address NM Command Summary Page Page Page IEEE 802 Family Relationships Page Record of Changes Page Index